Schaeffler LuK LFW193 Flywheel, OEM Flywheel, LuK RepSet Clutch Replacement Parts

Well...it's a little weird that the flywheel bolt holes are "keyed" and only installed one way, without any other keying to help you line things up, but you can't blame LuK for that.When my clutch blew, it was either get my existing 2000 Jeep Wrangler 4.0L flywheel honed or buy this new one. Honing was almost as expensive, but was discouraged. So I got this one.Seems to work great. In concert with the [LuK 05-901 Clutch Kit] I purchased, my Jeep drives better than new with no clutch chatter on a cold engine.One item to note...when removing a flywheel, you always should replace the flywheel bolts. I bought the [ARP (146-2801) Flywheel Bolt Kit] which fit my Jeep just fine.Also, you need a torque wrench. But if you are doing this work, you probably already have one.

As described. Sturdy, well made. I had a mechanic install it, along with a new clutch kit. The Jeep starts right up every time. No grind, no hesitation.

I installed this flywheel on a 2001 TJ. When I got the Jeep back together it ran rough and stalled. Codes were P0351, P0352, and P0353. I did some research and found out that others have had the same issue with this flywheel. The crankshaft position sensor doesn’t read it correctly. I had to redo the entire job. I cleaned up the old OEM flywheel and used it. Jeep runs perfect. Save yourself having to do the job twice!

Used to replace the flywheel on 1993 Jeep Wranger 4.0 5 speed. Fit just like OEM at no where near the price! Only have about 150 miles on it and the clutch kit (also from Luk) so far but it is working great! Highly recommend if your Jeep is your daily driver and occasionally you go 4 wheeling/mudding in the back country.

After hearing some horror stories about swapping out flywheels in Jeeps, I was worried about my project, but this Luk flywheel fit great and bolted up correctly (after i corrected two stripped flywheel bolts that is, not caused by this new flywheel but to listening to those who stated you could use the old bolts GRIN) Anyways after getting it all back together the jeeps runs good and shifts great.

If you have a Jeep wrangler Tj with the straight 6 engine and 5 speed manual ( or straight 4 with 5 speed manual tranny) this is absolutely the flywheel for you. When I opened I found packing grease on it to keep from rust so don't worry just blast it with break cleaner and put it in. Remember if you have the 6 cylinder torque it to 135ft pounds as for the straight four I am unsure I believe its about 115 but don't quote me on it. Either way this is definitely a great product. I would recommend that if you get the corresponding Luk Clutch kit to switch the Luk throw-out bearing with a National throw-out bearing as the Luk throw-out has plastic parts and plastic is a no go for a transmission and the reason to choose National is because they are a seasoned company making very reliable full metal regressed throw-out bearings for years. This product will be good for factory replacement and tranny upgrade

As the headline says it’s works great for my 94 YJ 4.0 Jeep. 100% recommended.UPDATE: 7000+ miles later and no issues with this flywheel. Great product for those looking to purchase.

Flywheel looks like a decent product except that timing cutouts for crank position sensor are wrong and vehicle runs really rough and throws CPS code. it cost me alot of money having the Flywheel replaced twice and by the time my mechanic could get the flywheel replace my return window was over. I conta<cted supplier and was never contacted back so I'm stuck with a Janky flywheel. Definitely will not work on my 1997 Jeep wrangler 4.0

great servicegreat productfair price (Co. needs to make coin as much as we need to save coin)very satisfied, eh

TODO EXCELENTE!!

Fits perfect, oem part for jeep 1992 4.0L engine. Good price also. Don't waste time refacing your old one, it could get too thin and run into problems with clutch releasing. And for Jeeps, refacing it not recommended because it would remove the slight curb on the facing. They are not completely flat with OEM.

RECOMMEND THIS FLYWHEEL CHEAPER THAN GET IT MACHINED RECOMMEND THIS PRODUCT.

I'm not sure you can get a fly wheel surfaced for the price of this one! They are not flat, and are actually concave. Machining messes them up. As advertised. shipped fast. no issues.