Magnetic Aquarium Anti-Jumping net Cover mesh to Protect Fish Jumping Out of Fish Tank

This was revolutionary for me! I have been in this hobby over 2 decades. Never have I seen a customizable lid like this, and if cut properly, you can raise one side to feed or take the entire mesh off after install. READ BOTH SELLER INSTRUCTIONS 2x CAREFULLY before cutting. The paper copy is the same as what's in the listing details. Be slow, and compare with the pictures. I found that I can even reduce trickle noise by allowing the mesh to go under the lip of the hang on back filter. Never will I go back to acrylic or premade lids. This is perfect for any square or rectangle, fits any kind of media, and it will last forever at an affordable price. It is easy to install, but you need to be able to follow directions and use a little critical thinking. I don't know if the mesh is measured for each customer, but I must've received 2.5' by 4' at minimum. This is only a 20 gallon, and I have tons of leftover magnet material also. I chose to follow the instructions for the strongest hold to protect fish that might jump. It is perfect! It has just enough cling strength to provide protection, but not so much that it's hard to lift while feeding.

This took me about 45 minutes, mostly using my very meager girly strength to try to clip the plastic into the rubber snappy part. However, this looks great and was easy to install. The only issue i had was the side clips were hard for me to snap in but i got it working. Two notes, the "leave a small gap" instruction is to fit in the very top plastic where it needs to snap down. just look at how wide it is and leave that much. I had to do a little extra trimming but that was easy to do. Also, dont lose the little square snaps! they are essential to getting it nice and tight and not all loosey goosey like some of the other reviews had. There was plenty to cover my 29 gallon and enough left to do my 5 gallon hospital tank as well. :) My one worry is that i have a bit of splashing up from an air stone, it may get gross quick.... but thats a problem for another day and the netting seems easy to replace.

The installation was fine and it works great if you have a low maintenance system. Magnets can be tough to reconnect which can cause you to drop one side into the tank. Magnets and water do not mix, especially when housing life. Only usable once too. Use egg crate or a custom made top for a permanent lid

The **7.5 FT DIY Magnetic Fish Aquarium Anti-Jumping Net Cover** works well to **keep fish safely inside the tank**, but I found the installation a bit challenging on my **125-gallon aquarium**. Doing it alone required patience and some juggling. By comparison, setting it up on my **75-gallon tank was much easier**. **Functionality:** Once installed, the magnetic net cover stays securely in place and does its job perfectly. The mesh is durable, and the magnetic closure makes it easy to open for feeding or maintenance. **Material & Quality:** The netting is sturdy yet flexible, and the magnets hold tightly without scratching the tank. It’s lightweight but reliable for preventing fish from jumping out. **Final Verdict:** This **anti-jump net cover works as intended**, but for larger tanks, it’s best to have a second person to make installation smoother. For smaller tanks, it’s quick and easy. A practical solution for any fishkeeper concerned about leaping fish.

Took a minute to figure out how to assemble, works great and the magnets are good quality. The clips to open it look kinda silly and are bulky but other than that I like it

Very easy to install, magnets are strong enough, quality is nice for the price. Some of the bad reviews don’t make sense on this product. It’s pretty straightforward to install and sticks very well if you clean the areas you are putting them on properly. Anyways, 10/10 product, definitely buying again in the future.

If I could give this zero stars I would. This may be the worst product I've ever purchased for my aquarium. In theory it should work but the problem is the adhesive on the magnetic strip doesn't even remotely stick to the glass. I followed the instructions to the letter I actually cleaned the glass with alcohol, dried it, put the magnet strip on let it sit. it didn't feel secure and it wasn't. I even put super glue on the corners when I sensed it coming apart. Then I assembled the rest of it and the minute I put any tension on the netting to get it to not droop in the water it pulled right off the glass and went in the water and once it got in the water it was ruined. Please do not buy this product. Unless you have another use for the screen, it is absolute garbage. My tank is 4' x 2' maybe on a smaller tank it would work - very frustrating

Works great! Comes in a big sheet of mesh and a long roll of tracks and magnets. You trim to size. Everything holds very well. The tracks that hold the mesh hold up really well. It's hard to push it together sometimes, but it means it holds up better. It doesn't say after it's been made which is awesome. My only wish is that it came with extra corners in the larger size. I have a breeder tank so it's long and has two openings instead of one long one. The support in the center breaks it up. So there's little corner pieces and I wish they would send 8 for larger sizes because larger tanks typically have a center brace which gives you two top openings versus smaller tanks have one single opening. Other than that this is a great product and I recommend it. Seller packaged it really well and shipping was on time.

Es ist etwas Fingerfertigkeit erforderlich. Da mein Becken mit 2 Seiten an der Wand steht

The idea is good, the magnet is good, but because of the plastic part, it is unusable, the plastic cannot be the soft type, very difficult to assemble, after a struggle and assembling it, the frame is arched and flimsy, I wasted this money

Oh heck yes! Lost another fish this morning. Lid is now on the non jumper tank! Super easy set up works amazing. Easily fits over cords for wave makers and heaters!

Does a gd job at keeping the fish in. A bit finicky to set up though.

An sich eine Klasse Idee aber oben auf dem Glas hält es bei dünnerem Glas schonmal gar nicht an der Seitenscheibe muss man wenn richtig sauber machen aber klebt trotzdem so semi gut wenn man nach etlichen wutanfällen es endlich Mal hinbekommen hat hält es ganz gut also 3 Sterne sind da ganz Fair 🙏