Grey PVC Quadrant Trim,Flexible Laminate Beading Self Adhesive Plastic Wall Corner Edging Strip for Worktop Ceiling Floor,Caulk Moulding Skirting Board Trim(3 Meters,19mm*10mm)

I used this to edge a new floor in my garden room instead of skirting board. I found it easy to cut and put in place but initially it did not stick well to the painted mdf walls. So I borrowed my wife’s hair dryer and heated it as I pressed it firmly home. The result….. a neat, well stuck finish.

Good product although I wish it was stickier. It seems to be okay after fitting but the instructions say to heat with a hairdrier for maximum adhesiveness. I couldn't do that as I'm unattached and bald :/ . However the ambient temperature was around 16C and it seems okay so far. Looks really nice though. As with anything, time will tell.

Bought this strip from another seller (1st photo) and although I liked it, it wasn’t exactly white-white and texture was rubbery so fluff stuck to it easy, then I bought this one (2nd photo) I thought I was getting exactly the same but this is by far better quality as it’s white as if it’s been painted so blends in with my freshly painted skirting much better and also has a sheen so easier to clean too. This seller is well worth saving

I was wary given some of the reviews, however...I got it to allow angling a Philips Hue lightstrip downwards at 45 degrees when mounted at the wall/ceiling 'corner'.The 19mm strip is perfect match for the lightstrip.Cleaned the wall/ceiling with isopropyl alcohol in the mounting area, then attached the strip. The adhesive grabs instantly and really sticks. On a wallpapered surface it's essential to position it into the corner correctly before pressing into place otherwise it may not fully stick to both surfaces, trying to move it will lift/tear the wallpaper.In retrospect it would have been easier with a person helping support the unstuck end of the strip during installation.Also wiped the strip with alcohol before sticking the lightstrip to it.The lightstrip runs warm, but there's no sign that adhesion to the wall/ceiling is affected even with the extra weight of the lightstrip.Edit...after less than a day from fitting, the adhesive failed overnight, the entire length just peeled away and fell down.The adhesive tape had even unstuck from the trim strip itself in many places (this happened with it cold, not with the lightstrip on.)It would not stick back, just unpeel again within a few seconds.As I've got the lightstrip stuck over the top, the simple solution was to remove the lightstrip, secure the trim strip with panel pins, then refit the lightstrip.The adhesive on the lightstrip seems to be much better.

This is absolutely rubbish! Is not self adhesive as described, you don't even buy it if you intend to use it as self adhesive. The is zero star, only clicked on 1 because I can't submit my review if I don't click on the star.

Easy to apply . Seems sturdy and well adhered to the top of the tiles. Happy so far !

I got this to finish off the join between my bath panel and floor tiles. The products feels high quality but does look a bit tacky due to the high gloss finish (personal preference I suppose). When the light shines off it, I hate how it looks. I will not score the product down down due to that.However, the adhesive (as others have said) is useless. I used a dab of superglue every 20 cm or so which did the trick, and it did make the tile and bath join look much neater. I also went around my loo with it, just to use up what I had left. I actually really like how it looks around my toilet. I may go around the whole wall tile to floor tile joins, haven't decided yet, due to how expensive that would be.It's easy to apply (using glue, not the adhesive the product comes with) and it's quite flexible. It's really difficult to mitre effectively, so I ended up just using electrical tape on the corners (little trick I learnt from Stacey Solomon). It did crack when I tried to go around a 90degree angle, so again, I just added a bit of elec tape to cover the crack. Worked a treat.To conclude, I would recomend this product, due to the ease of installing and the fact that it does neaten edges really well. However, you will likely need to use some different adhesive than the one provided on it.Ps. Please ignore the dodgy tile next to my toilet, I must have even drunk when I put that one on. It's usually hidden by something anyway. Ha.