3MMarine Adhesive Sealant Fast Cure 5200 (05220) Permanent Bonding and Sealing for Boats and RVs Above and Below the Waterline Waterproof Repair, White, 3 fl oz Tube

Good stuff. Messy to work with though

There’s a reason 3m charges so much for not stuff. IT WORKS! I used this to coat some rivets in my Jon boat while I replaced them. No leaks and this stuff seals great! I would recommend wearing gloves and having a rag on standby when using it. It can easily get everywhere.

Needed an adhesive/sealant to repair roof seam tape. Edges of tape lifted during hurricane Ian. Used this product to glue down seams using a small hard rubber roller. Worked well because cure time is quick. A bit messy to work with in this application but very well worth it. The prospect of replacing the roof tape would have taken days and cost hundreds of dollars. This method only cost me one tube of sealant and about 3 hours.

Sealed my aluminum boat rivets and worked great. Wear gloves and you won’t have any problems.

I've used this 3M Fast Cure 5200 for all sorts of purposes over the years, primarily on my boat. Whenever I drill a hole or put a screw into the boat's hull or transom, this stuff is going on the screw threads or in the hole to seal it from water permanently. I've patched holes up to 1/2 inch in diameter using just 3M 5200 and I've never had a drop of water get in through that hole afterward. It's pretty amazing stuff. I've also used this stuff to adhere loose trim to fiberglass inside my boat, it works well and bonds stronger than most glues on the market.The only downside to 3M Fast Cure 5200 is that it's messy and not very reusable. Even the small tubes are expensive. When you cap after using, make sure you find a way to use the rest of this sealant in the not-too-distant future as the cap will become difficult to remove, and the sealant will harden up near the cap. 3M 5200 sticks to just about every type of material on the planet and is impenetrable to water. For boats, 3M 5200 is a must-have, use it to quickly patch up holes and cracks, it'll keep your boat afloat without any leaks whatsoever.

There is nothing else that comes close. My records show I have purchased it 3 times from Amazon. Slow curing so you have plenty of time to position the part and then use something to hold it in place for 24 hours. Generally considered permanant - you will have to cut the glue seam to remove the part so don't use it on something that might need to be removed years down the road. Strong - you bet. I glued some flat pieces of metal to tubing on my boat. I can stand on these parts with all my weight. Pay attention to the directions - no alcohol cleaning prior to gluing. Can be frozen for longer life span. And NEVER wear good clothes while using this. Nothing will take it out of your clothes if you make a mistake. Use painters tape around the glue area to keep the 5200 off the surrounding area. Keep lots of paper towels near by - it is messy and seems to go everywhere by itself. Uses moisture to cure so can get wet before cured. And finally - guessing here - may be hazzardous to use in a fish tank. Lots of odd chemicals in this stuff.

When it comes to maintaining the integrity of my boat, I don't settle for anything less than the best. That's why I turned to the 3M Marine Adhesive Sealant Fast Cure 5200 (05220), and I'm delighted to share my experience with this exceptional product.First and foremost, this sealant lives up to its promise of creating a permanent bond. Whether it's sealing deck fittings, bonding hull seams, or securing hardware, the 3M 5200 forms a strong and durable connection that withstands the rigors of marine environments. I have complete confidence in its ability to keep my vessel watertight and secure, even in the most challenging conditions.The fast-curing formula is a game-changer, significantly reducing downtime and allowing me to get back on the water sooner. With its quick tack and rapid cure time, I can complete repairs and installations efficiently, without sacrificing quality or reliability. It's a time-saving solution that's essential for any boat owner.Durability is where this sealant truly shines. Designed to resist saltwater, weathering, and UV exposure, it maintains its integrity even after prolonged exposure to harsh marine conditions. I've seen firsthand how well it holds up against salt spray, pounding waves, and fluctuating temperatures, providing long-lasting protection and peace of mind.Application is straightforward, thanks to the easy-to-use syringe packaging and smooth consistency of the sealant. Whether I'm applying it to vertical surfaces or overhead, it spreads evenly and adheres well, ensuring a secure seal without drips or mess. Cleanup is a breeze, too, with soap and water easily removing any excess sealant before it cures.Versatility is another notable feature of the 3M 5200. In addition to its bonding and sealing capabilities, it can also be used for bedding and potting applications, making it a versatile solution for a wide range of marine projects.In conclusion, the 3M Marine Adhesive Sealant Fast Cure 5200 (05220) is a reliable and effective choice for boat owners seeking a permanent bonding and sealing solution. With its fast cure time, exceptional durability, ease of application, and versatility, it's an essential addition to any marine maintenance kit. I highly recommend this sealant to fellow boating enthusiasts who demand nothing but the best for their vessels.

Best sealant for boats buy far. Great product