JANYUN 3 Pieces Pen Shape Resin Mold Ballpoint Pen Silicone Molds Epoxy Resin Molds Resin Casting Molds with 75 Pieces Ballpoint Refill Pens for DIY Resin Crafts Making (Assorted Color)

Resin pens are the perfect gift for your teacher, your boss, friends, family...pretty much anyone that writes. You can make them bold and beautiful, fun and sassy, dainty and special, to match personalities to pen. Use your imagination and go wild!

I didn’t like having a flat side to the pen. This is my fault for now researching. The mold works great though and the pens write.

1 out of 3 comes good

There is a little nub on the inside of the mold and you must insert this into the end of the pen ink before pouring resin! Otherwise resin will clog the ink and it will not write!I have done this with all of mine and they have turned out wonderful.Great molds and great ink. Looks and writes beautifully.Love it. Will be buying extra sets to make more at once.

I absolutely love this kit. Super easy to use, makes beautiful pens, and the Ink/ballpoint write really well and beautifully. 10/10 all around. I take the ink cartridge and, leaving the red cover over the ballpoint, I put it in ballpoint first, then slip the other end into the mold but make sure the little nub goes inside the cartridge (this makes sure no resin gets inside and clogs it, causing ink to be unable to breathe) then I pour the epoxy slowly to avoid large and awkward air bubbles and once it’s been in for about 24 hours I slip it out of the mold, usually being able to bend the pen out so I don’t stress the mold, and I can either use pen right away while still a bit bendy or wait until it’s solid. Double check to make sure there’s a clear hole from exterior to inside of the ink cartridge otherwise the pen won’t work for long as the ink can’t breathe. If it got clogged don’t worry, just poke a tiny nail or a pin in the hole that’ll clear it up. There was a bit of a learning curve, first pen has lots of air bubbles, my newest is crystal clear. Highly recommend, I did rip a mold just a bit by being too rough with it (which is why I take the pen out earlier where I can bend it) But other than that it’s been amazing!

The media could not be loaded.  So I read that many couldn't use the pen and make it work after I bought the molds and before I actually made one...... I know bad decision... But I still decided to try. How I made it was: I used UV resin to make the end of the ink that needs to breath be the first thing I made secure. I grabbed the molds put the pens making sure the end was exactly in the spot that it needs to sit in the mold. Then with the UV resin I added it to that end only to secure the end not the whole pen. I dried it and did the same to the other end where we write. Once the two were secure, I proceeded to make the design of the actual pen in the middle. I only had UV resin so I was able to dry the pen quickly, though I will say that as long as you secure both ends for the middle we can use regular resin and let it sit until thr middle is dry. Once they were dry I tested them all and they worked. The video is actually me writting with them the next day. I do agree a cap is needed, I'm trying to see if I can find a solution for it but overall I liked them a lot. If anything I can show a better video or just send a message for tips. I added a picture of how the whole for the ink stays open allowing the pen to breath and it let's it write. Hope that when you try it, it helps!

My resin didn’t harden properly. It’s difficult to pour into and not sturdy. Decor is extremely difficult.I do not recommend.

I really liked the idea of being able to customize and use whatever glitter and dyes that I wanted to design pens. Such a super fun idea and I loved making them. The only thing is I did have trouble getting the ink to stay in place and getting the bubbles out that form at the tips of each end.

The media could not be loaded.  Watch fir air bubbles in the ends, and don't handle the mold too much due to the flex that will pop the refill out of the nipple support.

The mold is fine . The ink inserts don't work after a minute of use , making the 6 pens I made useless. I certainly could not sell them.

They work great! They write great too and make good little personalized gifts for fellow writers and peers alike. However, while I did get 3 packs of the pen ink refills, I asked for the red, blue and black pack. And all I got was black. I’m choosing to be optimistic about it though, as I didn’t get ripped out of a deal or anything, I was just a little disappointed I didn’t have 3 colours to choose from. Asides from that little mix up, they’re awesome and I’m super happy with my purchase.

Difficile d'obtenir un véritable produit fini (avec le même matériel pour finaliser un produit kustré, tous les stylos sortent mats du mouke utilisé). Ne donne pas le résultat décrit dans les images de publicitéTemps de séchage de plus de 72 heures pour s'assurer que le produit fini ne plie pas

Does not work very well , pen tube bends in a direction that sticks out the resin