Rockwell RK7241S Table Saw with Laser

I don't write many reviews, but this table saw deserves one. If for nothing more than the fact that it doesn't have enough as is. So before I begin, I must preface this review letting you know that I'm upgrading from a $100 Craftsman that I've been using for about 12 years. I am a DIY, weekend warrior type, so not a professional by any means. My budget was also not large enough to spend on a cabinet saw, so that left me in the "contractor" arena of table saws. So onto the review...The table setup was super simple. Lifted it out of the box, flipped it on end, lowered the legs, and set it upright. The knobs that lock the legs in place, just take a half twist to unlock, and then when you begin opening the legs, you give them another half twist to allow them to lock into place once the legs are open.The first thing that you will notice is that with the exception of the manual and dust bag, there is nothing left to pull out of the box. That's because everything is attached to the saw in its own place, including a spot for blades, tools, fence, push stick, shield, and miter.Next was opening the extension. Just press the little spring loaded clip and open the extension. I saw one mention in my research where someone questioned the extension hinge. This was a point of question for me, but not anymore. One, the hinge seems decent, especially knowing that you won't put hardly any weight on that area. Here's the thing. The extension table sits almost 1/2" lower than the main table, and this is by design. For most materials, they are thick enough that the extension is not needed for support. It's mainly there for the fence. However, if you are running something thin through and want a bit of support, then there is a support bar that you can attach to the fence that would give you this extra bit of support. What else is nice about the extension being lower is that it will reduce drag on any material that you are running through the saw. So for these reasons, I'm not concerned about the hinge at all at this point.Blade installation was next. The throat plate is a tool free plate that just pops out and back in. This is good and bad, in my opinion. The good is that it's really easy to pull out to replace the blade and to install/remove the riving knife or shield. The bad, in my opinion, is that I was hoping to build/buy a zero clearance insert. With this design, I'm not sure yet how or if that will be possible.So after I got the plate removed I just used the 2 wrenches that came with the saw to install the blade. Not much to say here, other than it was nice and easy, especially compared to my old Craftsman. While I had it open, I also installed the riving knife. There is a lever behind the blade that you just flip to loosen the clamp-style mount for the knife or shield. Just slip in the one you want and lock the lever. After that, I popped in the throat plate and was ready to go.I then set up the fence. When I received it, the fence was not perfectly parallel to the blade. In fact, it was about 1/16" tighter at the back. The nice thing is that this is completely adjustable. I made my adjustments, and it's perfect now. The fence slides reasonably well along the rail, clamps tight, and holds solid. You can also adjust the "window" that shows you your measurement to make it as accurate as possible. There is also the ability to adjust the tightness of the clamp. Neither was necessary to adjust.The laser was next to be set up. I installed the included batteries, and that was that. The switch is just to the left of the main power, so it's easy to flip on when you flip the other. I am kind of surprised that the laser requires batteries when it could have been just as easy to tie it into the table power. Either way, it's easy to flip on and off. As for the function of the laser, the jury is still out. Basically it shines a laser line on the surface of the table, and not the wood itself. This may be ok, but it appears to me that the line is just too close to the front of the table so it may be a trick to use for larger pieces. One other thing to note is that the laser is not adjustable. I did not test to see how perfectly aligned it was, but it did appear pretty accurate. All in all, it's something to advertise, but I doubt that I will ever use it much at all.The out feed support is a really nice addition for me. Always used rollers or saw horses in the past to accomplish this, and now those aren't required. Not much else to say about it, other than it just pulls out from the back of the table, and provides nice support for anything up to about 2 feet in length without teetering.Haven't played with the bevel much yet, but appears to be quick and easy to adjust. Just unlock, slide to the desired position, and lock. Not sure how easy it is to fine tune, but initial tests didn't seem too bad.Dust bag seems decent, but definitely didn't catch everything. It was able to catch a majority of the dust and debris, but not all of it. Sadly there isn't a connection for a shop vac, but I believe that this could be built on with a little bit of ingenuity. That will probably be my primary tweak when I have the time.Last thing to review is the miter. It is plastic, but I suppose that that's to be expected from this price range. It slid through the slot nicely, and when there was lumber on top of the guide rail to hold it flat, there wasn't hardly any play from right to left. If you do not have anything sitting on top of it, you can wriggle it from right to left, but that's because it's lifting a bit in the t-slot. When held flat, it's a nice tight fit, with very little play. Other than that, it slides smooth, and will do the job. Oh, and there is a hole on either side of the handle that could be used to mount a wider support for better control if desired.All-in-all, this is a very worthwhile upgrade in my opinion, and I am very happy with my purchase.

This is one solid saw, espcially since it's a "jobsite" saw. On the doorstep, out of the box and setup, maybe 30 minutes. Setup was a breeze and everything is within about 1/64"; more checking and possbily some tweaking needs to be done, but it has already performed well above expectations on the first use.I'm on a budget and couldn't afford a cabinet saw so I got this and the  Rockwell RW9189 Table Saw Sliding Extension Table Attachment for RK7241S Table Saw  [I have a seperate review on that.]Point being, I needed to cut some very accurate templates for a large set of bookshelves and these two items made that a breeze.Although this is basically my shop saw, the ability to fold it up and store it away is a big bonus and no additional adjustments are needed; just pull it out, fold out the legs and go.A couple of shop built accessories (an outfeed table, possibly an infeed table and a couple sleds and I expect great things out of this machine.HIGHLY recommended!

Is this a great saw? No. Is it a bad saw? No. It's good for the price. I've had many brands of contractor saws and permanent table saws over the years and thought I'd try this one out around the house and not "use-up" my dewalt that I make a living with on honey do's. Here are my cons. The dust bag is worthless. The saw dust goes everywhere except in the bag. The releases for the legs are finiky and hard to reengage sometimes. The blade it comes with is junk. Use it as a coaster or frisbee and save yourself the time of changing it later. The instruction manual is incoherent. The attachment point for the roving knife is a pain to use. The deck on this thing is shiney. I actually had to take some fine grit sand paper to it to de gloss it as I was getting sun blinded when I used the thing outside. The motor isn't the smoothest. I wouldn't attempt to use this for fine finish work due to the vibration. Those are the cons. Here are my pros. The fence is accurate. I checked it over and over and I used it from ready other reviews and the motor, blade, and fence all were true repeatedly. This thing has a push block and roving knofe included and everything packs up nicely and had a proper, secure place. The material extension on the back and the fold out support on the side are very welcome and useful. It is a heavy unit but transports easily and rolls nicely. The miter gauge is ok. Not the greatest quality and I wouldn't rely on its degree marks but it latched down securely and slides smoothly. The blade height and angle are easy and quick to adjust. It has an adjustment foot on one of the legs to level the saw. The deck is FLAT. Is this the best saw made. No. Is it the best saw at this price. I probably think so considering the features.

Es práctica y versátil, se adapta a mis necesidades, tiene muy buenas prestaciones, es cómoda para transportarla y para a almacenarla. Me gustaría completarla con la mesa de extensión deslizable, pero no la veo anunciada en este medio. Excelente producto.

The handle that tightens the blade guard broke when I installed the guard and the laser is useless, when they primed the saw they got the laser window primed so I thought it didn't even work. After I got the primer off it makes a dull red line on the table that you can't see once you put wood on to saw, so big deal. Other than that the saw seams okay.

Watch out for blade alignment. See reviews on Amazon.com. Very hard to contact manufacturer. No adjustments. Manufacturer did send new saw which was ok.

Great saw .. Does everything I need .. The only thing is I can't find the sliding table extension anymore