AZDelivery 5 x compatible with FT232RL Mini USB to TTL Serial Converter Adapter Module 3.3V 5.5V FT232R Port DTR RX TX VCC CTS GND Pin compatible with Arduino and Raspberry Pi including E-Book!

Perfect solution to a broken interface board on my pixmax viynl cutter.No issues with drivers and worked with laptop first try.

My use case was to program the ESP32 CAM ModuleI found the 3.3V line on these modules a bit underpowered to program the ESP32 CAM module (brown outs and errors), but there is a simple solution: Set the jumper to 5V and connect the power output to the 5V line on the ESP32 CAM. My guess is the ESP32 CAM uses a bit more power than intended for this module to supply.Otherwise a great product, does exactly what it is intended to.

I bought a pack of these to flash an ESP32-based Sonoff smart relay, after having tried a CH340G-based adaptor that turned out to be defective. The first FT232RL adaptor I tried worked fine, and was detected automatically as a COM port by Windows 11.Pros: A jumper lets you select 3.3V or 5V data output, so you don't fry delicate 3.3V devices. All the main comms lines are broken out to headers (RTS & CTS, as well as the normal RX, TX, Vcc and GND), and there are lots of handy through-hole connections for other lines.Cons: No Dupont or USB cables included, and the connector is Mini USB, rather than the more modern Micro or USB-C, so it's harder to find an appropriate cable. The screen print on the board is very close to the header and jumper block, so it's hard to see which cable is which. Although the adapter worked fine for flashing the Sonoff device, it couldn't supply enough power to allow the ESP32 to fire up a WiFi connection.

Good

Excellent product.The reason I gave it 5 stars is it comes with pins already soldered and it has a simple jumper to switch between 3.3v and 5v as opposed to most FTDI where it's a solder jumper.It worked great once I figured out the mini usb cable I had lying around only had VCC wired.It was plug and play on Win 10 64 bit.

Arrived on time and packed in a sturdy cardboard box containing an antistatic envelope surrounding the product itself. The product was quickly put into service flashing software onto an ESP32-CAM board which lacks the on-board USB-serial converter that most of today's microcontroller boards include.I plugged the module into a USB port on a Windows 10 laptop and, after a short delay, it showed up as COM7, no driver installation needed. Drivers for Windows, Mac and Linux are easily found on the Internet if required.I connected the serial and power lines from the module to the ESP board with DuPont wires and shorted out a link to put the ESP into download mode, then compiled and loaded the software via the Arduino environment. All went without a hitch, despite some of these ESP boards having a reputation for being tricky to flash.Cut/paste of one of the messages on Arduino console:"Wrote 902304 bytes (487502 compressed) at 0x00010000 in 11.9 seconds (effective 604.1 kbit/s)... "Conclusion: Does the job well, useful addition to the gadget toolbox.

These devices work to connect Arduino Pro Minis via USB to a host PC.However, the documentation suggests crossing over TXD and RXD lines, as might be expected. However, this is not so. TXD to TXD and RXD to RXD works.FT232RL Pro MiniGnd ---------Gnd3v3 NC5v -----------5vTxd----------TxdRxd----------RxdDTR----------DTR

It works just fine on Linux Mint after I installrd the software for it but have not been able to get it to work on Windows 10 yet.

Aucun problème, directement reconnu par Windows et la liaison série fonctionne parfaitement.

Works out of the box, IO's accessible both by pins and through hole.

Perfecto, funciona como debería. Un poco anticuado el puerto usb y no trae cable. Por lo demás va de lujo

Works great for ps5 uart if it does not recognise on windows make sure to download from latest official FTDI VCP drivers and plug into a usb 2.0 port :)

It works out of the box. It would be nice if the usb connector was microusb or usb-C, but that is a minor thing.