KratorJBM-068-B Black Turn Signals (2pcs Heavy Duty Motorcycle Bulb Indicators Blinkers Lights)

These are actually nicer than expected. They're kinda heavy and well made. There is an oring seal to keep out moisture. The grill can be mounted horizontal or verticle and its held in by a screw. The lens is nice and is faceted instead of just smooth. It comes w a 10w bulb I may put a higher wattage bulb in it if it's not bright enough, a standard running light bulb is ~8w.

OK Sure these are not the highest quality lights out there but they are a really cool design and a really good start for some awesome lights on just about any bike. First off, the bulb that comes with it is cheap, the reflector is dull (zinc plated) and the wires are very thick making the need for the very thin hollow bolt that comes with it to mount it. I took both of them apart, removed the light socket by pressing it out of the reflector and then polished it. Next I used a set of red LED bulbs and inserted them into the lens, glued them down and soldered a new set of thinner wires to the bulb. NOW they are rear marker lights and turn signals that I can trust. I also drilled out a 3/8-16 bolt for the mount bolts, so that I would not have to worry about the thin little mounts breaking, like a few people have reported. So basically, if you want a set of cool lights that bolt right up and you can depend on (out of the box), order a set of Kury Akyn lights and quit being a cheapskate. If you have the ability to make something, these will be much cooler, but they take some work. The light casing itself is all I wanted and I'm not disappointed. I will update this and add more pics as the project goes on.

I want to give them 3.5....but that rounds to four. So four it is. They look good. They're simple. If you're even a little bit of a DIY'r than buy em! I hooked them up and the one I chose for my left blinker stopped working in about an hour. They come with a black, red, and brown wire. I don't know why, the black is ground and the red and brown seem to both be positive. On every system I've worked on (which has been somewhat extensive) I've only ever needed/used 2 wires for a low wattage incandescent bulb; +/-. When I was finding the fault I found my fuse had blown, and the red wire no longer applied power; it was a 10amp fuse, so I'm sure it just shorted due to cheap wiring. I used the brown wire and the blinker was restored. They're not very bright, but you can rewire/insulate some LED's which is what I'm going to do and have a nice looking, powerful blinker on your bike.These may work out of the box, but have a lot of room for improvement. But it's nonsensical to give them a poor rating when they're so cheap. Most people agree that you get what you pay for; and I think these are a great bang for your buck. I converted my 2012 CBR250R into a streetfighter using inexpensive parts from this company and making slight, mechanically inclined modifications and my bike looks, and functions very, very well.

I have an all blacked out bike (Murdered) and these lights are perfect. They are just a bit smaller then most stock units and are still big enough to see. The quality is great for the price and the look is awesome on a black bike - Highly Recommend.

Signals are well machined and look good, however one screw to hold cap on housing which is very small, was cross threaded, sticking out halfway with stripped head. This shows poor final QC and now I have to search out right pitch thread and replace cross-thread one. I hope there are enough good threads left inside housing. A little annoying for an item that is otherwise good construction.

these are great turn signals, very heavy duty and i enjoy that there not LED and i like that they are metal dont hesitate because of the price i did for a while thinking they would be junk but they are not at all! Great product!

Cheap badly engineered junk. These are three wire Turn Signal AND Running Light capable with dual filament bulbs. UPDATE: All four I purchased have broken in less than 4 months and have caused grounding faults of all kinds due to their faulty design. The housings are sturdy enough but the hollow studs are weak and break off easily. Also, the interior bulb housing is metal and completes the circuit with the outside metal housing which causes a short in your system if you install them on a grounded mount (any frame part). Most mounts are metal and if connected to your frame, they will be grounded too, and this will cause problems or faults or even sparks. I had to re-wire, drill new wiring holes, affix new solid bolt mounting studs and remount on my motorcycle to get them to work again. Even after insulating the interior bulb housing with electrical tape the tiny screw holding the lens cover on contacts the interior housing and completes the circuit as well, causing a fault. There are not worth the price I paid.

Bulbs are hard to find and not a standard motorcycle or car size. Nice heavy die cast metal case and rough sand cast texture look great but the plastic lens rattles around behind the cover. They aren't weather sealed either, and are a serious pain to clean. If you ride in the rain, road grime will practically block out all of the light from them. If you just drive local, they would be OK, but I wouldn't recommend them for any type of distance riding. Also the screw which retains the cover is low grade metal and will start to strip out the first time you remove the cover. Also, the mount is a drilled out all-thread stud. I had trouble keeping them tight.

Exelente calidad de las unidades en su acabado.

Great little lights. Only issue is that because they are so small they use a small dome 1157 style bulb. So i had to search high and low to find an LED equivalent to convert them.I purchased the led conversion bulbs off amazon but they have yet to arrive. I will continue using the bulbs as-is until they break a filament. I made custom brackets to hold these lights and they have no vibration dampening so i figured it is only a matter of time before they break but so far they are holding up (even with really bumpy washboard dirt roads in my area).

De muy buena calidad 100% recomendado

The media could not be loaded. Decent quality lights. Halogens so no fast blink like LED’s. 3/4” stuff for mounting with wiring ran through already and wiring is cased in a simple black sleeve. Rather heavy but feel durable. Nice addition to my bike removing previous bullet LED’s.

Solid build, very happy with these lights. I wasn’t expecting anything spectacular for the price, but when they arrived I was extremely satisfied! Easy to mount and hook up, and look awesome when they are on! With that being said I docked 1 star because I had to pull one light fixture apart to adjust the contact in the back to make it work, but other than that I couldn’t be happier!