DROKCNC DC Buck Converter with Meter, 6-70V to 0-60V 10A 600W, DC 5V 9V 12V 24V 36V 48V 60V Fixed Output Voltage, Adjustable Power Supply Voltage Regulator Step Down Module

I have had good results with DROK products and when I was looking for building my own power supply using a toroid xfmr, rectifier, cap that had on hand - this DC-DC converter with a nice remote control/display assembly fit my needs perfectly. My power supply "back end" is able to produce 45 vdc at 4 amps and via switching the xfmr leads I can parallel the two secondaries for 22vdc at 8amps. I purchased the DROK model sold for 1200W to make sure I didn't stress the converter board in my application.Since my purchase arrived I've connected misc loads testing the DROK converter. It has worked perfectly so far. While I don't have a handy load to really stress the full power rating; it has handled my 5-150 watt loads using the 45 vdc input with no issues. The small cooling fan turns on automatically when loads over 50 watts or 2 amps are in use. I initally had my doubts the heatsink/cooling fan would do the job given the ad indicated up to 5-6 volt "overhead" used by the converter. So far I have seen around 2-3 volt overhead for my tests and that makes me a lot more comfortable.Prior to initial testing I looked over the converter board carefully for any workmanship concerns. I was pleasantly surprised to find everything clean, neat, and nothing that raised a concern that the unit might fry and die in my first application of power. In fact the only really minor thing I found during my inspection was the rectangular plastic cover over the display was attached skewed. Hardly a problem! Also, it's not mentioned in the front/back single page of instructions but when you cycle through the power/capacity/energy/time parameters using the encoder button you will also get an operating temperature reading after the time parameter which tells you the converter board temperature in degrees C. A nice feature when working the converter at high voltages/currents.One other oddity I found with the instruction sheet parameters is that the overcurrent protection is listed at 16Amps and output over power protection is set at 950Watts. Those don't match up to either the 0-10 amp or the 0-20amp models listed on the datasheet. For my purposes the default settings are fine but might be a concern for others wanting to use the maximums of this converter.I have no use for the serial communication interface or the fixed output voltage settings so can't help any reader with those aspects. The display controls take a few minutes to understand; but one thing I found helpful is just being patient and letting the timeout take effect rather than cycling through additional features/functions. There is a useful key/interfaces table on the supplied page of instructions that I found very helpful.In use, you will need to get used to a ramp up/down during power on/off. Think of it as the controller is constantly measuring the output and comparing to the setting. This results in the output voltage ramping up from 0 to say 15Vdc over a second or two - slow start so to speak. In addition you will likely see a small overshoot to your voltage setting in order of millivolts to 10's of millivolts. For a 12vdc fan test I would see the voltage overshoot to about 12.24 and then settle back to 12.0. During power off the voltage would gradually drop to 0 over about 3-4 seconds. Also, when power is initally applied to the converter the display will show zeros for everything for first few seconds and then display the last voltage/current limit settings. Best to wait to turn on the load until after you see the display has the desired settings.So far I'm very pleased with this DROK converter - exactly what I wanted for my power supply project and with the additional AH/WH/Time features it would be a nice addition for a solar/wind/battery system when need a lower DC voltage than what the battery bank provides; i.e., few hunderd watts of 12vdc from 24 vdc battery bank. Now I just need to get busy cutting a mounting hole for the display in my metal cabinet!

Once I got the mounting setup, this took me minutes to setup. Easy and straight forward operation. Used it to step down an 48V UPS battery output that was over driving to 56V. Work like a charm. No issues supplying battery power to the Access Control system while power is out. It gives a nice wattage and ampier output reading on the LCD screen too, making my battery calculations a sinch.

I have solar panels with an open circuit voltage of 68 volts while the power bank I purchased takes a max of 60V, so I needed exactly this kind of converter. I have the 1200W variant.I mounted the board and control panel in a nice little project box from elsewhere on Amazon, and I admit I was a bit surprised to find the converter doesn't even get very warm handling 600W. Its little fan is functional and effective. Per my inline meters, the power loss through the unit at e.g., 62V and 9.4A input is quite small - only about 3% or 4%. An example reading I've been seeing in practical use is 583W input, 564W output. The status display is readable and it matches my other monitors within a percent or two. I like that it has a lot of useful settings like voltage and current limits, auto-on, etc., and they do work.My one complaint is that the input and output terminals are pretty small and close together for handling 1200W. Be careful when you are wiring things up to this, especially if you have thick wire.It really works and I honestly expected to have to pay a lot more for this functionality, but there are newer designs (e.g. on Ali Express) that are more efficient and have more features.

Received package in good condition wrapped in plastic bag and in a box, when i opened one screw is missing from IN connection part.not that important i have extra screws. However the IN and OUT part to attach the weirs to it is so close together and so ,extremely ,extremely small that's impossible to attach any kind of right size wires to it. this is sold as 1500 watt device, so for example you want to connect the inlet to18 volt and outlet 12.8v that's connected to a 300 watt inverter, you need to use a 10 or 12 Gage weir and its impossible otherwise have to use some micro weirs, you may cause fire. Poorest engineering and design.

Meters reads actual current and voltage. Used 2 for a dual +/- supply didn't cause any problems like some switching supplies do.

This product was delivery in a plastic bag without any protection, it was missing all the screws for the in/out connections, absolutely ZERO instructions. Amazon sent me to the seller, the seller sent me to Amazon, and round and round we go. I figured out how to get it to work, spent an additional $10 on replacement screws. I cannot recommend this item to anyone due to the lack of support for the unit and the merry-go-round from the supplier and the seller. Drok doesn't care to support their products and information couldn't be found on the net either. Unless you are looking for a surprise product, I recommend choosing a different seller, just sayin!

great

Great