ARCTIC TP-3: Premium Performance Thermal Pad, 200 x 100 x 1.0 mm, (stackable to 2.0 mm without performance loss), 2 Pieces - High Performance, particularly soft, ideal gap filler, bridging gaps

0.5 is very thin, one side has easy to remove blue backing, other side has clear plastic that given the thickness can be hard to remove without ripping/tearing the pad Otherwise good product

Works great on my..." Toshiba 10TB Enterprise Internal Hard Drive" that was running hot.

good quality

Performed well. Big pack, so lasted a long time.

I have a 9 year old Samsund laptog. And the fan had become very noisy. I was thinking of replacing the fan. But then I had another Idea. I took the fan out anr replaced it with one Arctic TP-3 Thermal Pad. 200mm x 100mm x 1.5mm My laptop is much quieter now. That's obvious, I don't neerd to tell you that. I wish I could be more scientific. But it depends also on what the laptop is doing. Certainly the result is satisfactory. My laptop is not overheating. My impression is that it is running cooler with the thermal pad than it was with the fan. And the battery life is a little bit longer because the thermal pad doesn't use any power. I'm happy all round. As I said, I'm not recommeding to anybody that they remove any cooling fan from anything. I did so with the utmost caution, monitoring nd testing as I went along.

They are definitely thermal pads 👍🏻 Used on console memory chips when repasting the CPU, can't go wrong with arctic

Will not separate from clear back plastic without tearing/folding. Cannot recommend this brand

Çok kaliteli Ps4 pro için kullandım süper oldu

The front plastic covering sheet is a little annoying to remove and can cause the pad to split but other than that, it works perfectly and I have not had any issues after a week of application. The cut pads can be stacked as advertised if you need 2mm pads and I had no issues with stacking some of them.

Molto soffici e stackabili, al miglior prezzo per metratura che ho trovato (100x200 a 20 euro). ideale per realizzare backplate attive DIY nelle GPU ove non presenti di fabbrica, migliore dei pad stock nel mio caso con una 3060 invecchiata 2 anni. IMPORTANTE!!! non toccate personalmente le GPU se non sapete *esattamente* cosa state facendo.

I used ARCTIC TP-3 (1.0 mm) for a thermal pad mod on my old 13-inch MacBook Air M2 (16 GB). I have since upgraded to a MacBook Pro, so this MacBook Air is now my girlfriend’s laptop, but I did the mod while it was mine and it is still running that setup today. My goal was better short-burst performance under heavier workloads like Parallels, where I could see the CPU spike and then throttle quickly. After this mod, the throttling behavior improved noticeably for my use, and apps that used to feel sluggish to open or compile in Parallels became much more manageable. Important warning about fit: do not copy what I did the first time. Because the sheet size almost perfectly covered the entire logic board area, I tried covering basically everything. That was a mistake. Reinstalling the bottom cover was way harder than it needed to be, and most of that extra coverage was unnecessary. If you are doing this type of mod, I would only cover the area that actually benefits, which is the region over the SoC where you want the pad to contact the bottom cover and spread heat into the chassis. Covering the whole board just adds frustration with little extra benefit. Also be ready for heat. The whole point of this mod is that it dumps more heat into the bottom chassis, so it can get legitimately hot to the touch during sustained load or gaming. In our case, it is still worth it. My girlfriend mostly uses the MacBook Air in bed with a cover/blanket underneath, so she does not feel the heat directly. The extra thermal headroom is also helpful during long sessions, like being on Discord for a while while video streaming at the same time (plus noise suppression), since those workloads can add up over time on a fanless laptop. If you are comfortable opening your device and you understand the trade-offs, this pad is extremely effective for the price. It is a high-impact mod for fanless machines, but plan your coverage carefully and do not overdo it, or you will fight the reassembly and end up with a laptop that runs much hotter on the bottom.

Es costosa comparándola con otras marcas pero es mucho mejor.