Triton Work Clamps for TTS1400 TTSWC Work Clamps 320mm (332891)

Nice fine finish, will see how long it lasts, but brilliant value.Just a caution that in some deep bevelled cuts in softwood it has bound and kicked back, but don’t be foolish like me and do those cuts with a lower tooth count blade or in two passes.

Was recommended to me

very handy square for my festool track saw, saves time squaring up at both ends of sheet materials.the only advise i would give is lubricate the threaded parts inside and the threaded bolt as the 1st on i had cross threaded so i used some PTFE silicone spray or you could use some grease,amazon were brilliant at replacing the 1st damaged screw, very fast replacement, well done amazon!!!!!!!

Good build quality. Crazy expensive for a pair of grips, but they fit the Triton rail profile. Most of the time I am cutting longer or shorter rips, so the profile grips are no more effective than any other clamp. However, when you can clamp to the end of the rail they work perfectly. Mine arrived in all-black rather than two-tone.

Made of heavy nylon and saw fitted perfectly in bag easy velcro to close ,quality and goodprice

This works well with the Triton track. It isn't universal. Required some tuning up.

Having recently broken the bank and bought a Festool track saw I was looking for a cheap way of making consistently accurate and repeatably square cross-cuts. I came across this on Amazon for £25 and thought I’d give it a go. As others have said, there’s no manual and it didn’t cut square out of the box but it is very simple to adjust for square and attach to my festool guide rail. Once set up, I did a 5 cut test on a 600 mm square piece of MDF. Basically cut each side of the square, each time referencing off the previous cut edge, just a thin trim cut. The fifth cut is back to what was side 1; this time taking about a 10 mm cut. I measured the two ends of my cut-off piece with digital calipers and got a 0.5 mm difference. As the test multiplies the error four fold (one time for each cut) this gives an error of 0.125 mm over 600 mm, certainly good enough for my woodworking. There are other guide rail squares on the market for 8 x this price but they certainly won’t be 8 x more accurate.Highly recommended.

I bought this rail square an absolute age ago. I tried to use it with my Makita track, and - despite what others have said here - it does actually fit. If I'm not mistaken, I think I paid less than £20 when I bought it, but it was, I'm sorry to say, £20 wasted. At £49, well, Just don't bother! This is a one-trick pony - assist in making square cuts with a tracksaw - and it failed miserably. Even on short rips of 400mm it was over 3mm out of square. I was able to use tape to correct this to some extent, but I just went back to using the speed square for a more reliable cut.I have, since, upgraded to a proper rail square - the blue brand - cost more, £80 from Axminster, pre-pandemic, but is actually works! Full length rips are now bob-on. With the price of material these days, it just doesn't make sense to skimp on something like this. Don't get me wrong: it doesn't have to be Festool all the way, but when it comes to tape measures, squares and rulers, definitely go that extra mile, and save yourself grief and money in the long run.

J'avais déjà la scie plongeante et le rail Triton et il me manquait les serres joints.

Pour scie plongeante triton 165mm, les deux rails sont en état neufs non abimés dans l emballage Triton d 'origine. Le tout livré en deux jours, parfais.

Genau das was ich gesucht habe, macht was sie soll und das auch ziemlich genau!Für meine Zwecke genau das richtige

Needs to be fastned onto the rail with an angel to get it to exactly 90degrees as it aint snug into the rail socket. But once fastned with a square it works like a charm.

One of the worst things I have bought in a long time...Says it works with the Dewalt track,(terribly) on a 59" track it has over an inch of slop at the top end ..no way to fix it correctly due to the receiver being to narrow....terrible tool