60A SL V2 Brushless ESC for 1/10 Car - RC Speed Control - 1x Hobbypower Racing 60A Brushless ESC - Teen, Adult

i play with set buttion to set up to change setting it was not eazy i miss it up i was screwed .i went and buy led program card and i had set the way i want it in min. it run great . i highly recommend the led program card version 2 hobby wing for exrun x rum series will work with this . just plug you black connector from esc into it turn power on esc . you will see line and goes blank for a second than the number will light up press item 1 to 12 on your chart and press vaule to change number hit ok exsample 1 running mode if you want forward reverse and brakeitem 1 and vaule is to and hit ok . this unit has 11 item running mode dragbrake force punch level brake and reverse speed and timing over heat protectection and motor roation and lipo theidhold for lipo to use nicd oe nihh battery you must shut off the lipo shut of to nonprotectection if not your first run it will die when hit the trigger item 3 vaule 1 ..on some brushless motor if you have the motor wire right it will go super slow in forward and racing speed in reverse ..to solve this problem .blue to blue is right criss cross yellowto red or orangeand swich the swich on tramiiter for it to work . are diffect i mean blue to blue is right a b to b c to d criss cross them some motor are diffent like neewer turnigy exsample it not water proff don't get it wet i,m running 3900 kv motor with this unit some off this come with the oldschool white tamaya plur or some of this are start coming with dean plug .the esc has 3.5 female bullet conector on motor .if exsample you motoe has 4 you need adapter buy electro fly 3123 so you can plud male into esc and female bullet will go into motor or you have to change plug so it will fit it lot chaper to get this and not sped 80 or over i get about for month out of this unit rthan replace it

Would give it zero if I could. Awful esc, mine was defective or something because I hooked it up to a tacon motor and it was awful. Tacon motor was fine, but it screwed up the how the motor perform and the servo. Just don't buy this go for the hobbywing, aka an actual brand, plus it's waterproof. Or be smarter and buy a 100 castle system. If you look at that you would be getting a non water proof low grade system for around $75 compared to spending that extra $15 to get the good stuff. Overall wouldn't buy, people and customer support were very nice and gave me my full refund

Despite the esc being rated for 3s, the manual states that the fan is NOT 3s capable, and would need to be replaced or rewired.After replacing the fan, this ran fine in my short-course buggy.I also tried it in a monster truck, but the system kept browning out, indicating a weaker BEC. If you're looking to run this in a larger truck, an external BEC appears necessary.

I bought this esc a few weeks back, well after only one use the esc stopped working. At first I thought it was my ,also new, motor that was defective, but I just received the replacement last night and upon installing it, it didn't work. At this point I made the conclusion it was the esc that was faulty. I did order a replacement and I'm hoping it's was a fluke. I will update when the new unit arrives and I hopefully get more then one use out of it. 2/2/2016

Very impressed with this esc. I really can't complain with the price and the performance it gives. Iv bear the hell out of this esc with a 3s Lipo and 4200kv motor and it refuses to die. I also just found out that it's the same esc that comes on a stock brushless dhk from hobby people. So I can't imagine it being bad if they are mass produced and sold in one of the biggest hobby stores. Buy it. Programming will probably be the biggest pain but will pay off when you get it going.

Bought this with a Hobbywing 13t motor bc I heard great things about Hobbywings products. Unfortunately this one was bad and whenever the engine ran for about 5 minutes it was in and out. When setting it up it the menus did not match any of the handouts as in settings. There was an extra setting and for the punch setting it only had 4 instead of 8 choices. I emailed Hobbywing and they did respond. I then sent in a video and pictures but they support has yet to respond on the new pictures. I did get a "we have never seen this before. I tried every setting possible, then replaced the Tamiya plug after it melted on me and I wasn't using a Lipo battery. It appears many people have good luck but it's a hit or miss with this one. I love the setup and the way the esc stays cool at all times. I dont like how the temperature control does not work nor do I like a menu that doesn't match any of the manuals. Although this one didn't work I am still going to buy another Hobbywing ESC. I just like their products and their dedication to the sport. I did not get my issue resolved was impressed but an Hobbywing's attempt to help me out. I'm not really sure if Hobbypower is a Hobbywing product after looking back.I took a risk based on the reviews and knew it was a hit or miss. I think Hobbywing is a good product line so I will replace with a higher level product and see what happens. I have the feeling in this case you need to pay a bit more to get a solid ESC. On this one I gambled and unfortunately lost. Pay more and get more with an ESC. Hobbywing is a good company so let's see what happens with the next one. I returned this Hobbypower for a Hobbywing ESC spending about $75. So, get a good one right off the bat and save yourself some hassle. I did get a refund from Amazon which was good.

I've got 4 or 5 of these.I've had the first one for at least 7 years. Used it originally for speed runs in my Bandit. Bought it with a motor for $90. That was cheap at the time! Never had a problem with it.The rest are in drifters, touring cars, and monster trucks.I have 25 amps, 30 amps, 45 amps and 60 amps.All work great.

I just got this esc yesterday and today i tested on my rc10 t3 pair it with a 3500kv traxxas motor and this thing its a beast, 2s good for bashing on 3s I'm gonna have to add some weight to the front and adjust the punch, works really good out of the box, no binding just palli plug and play