Magigoo All-in-One 3D Printer Bed Adhesive Glue for ABS, PLA, PETG, 50mL | Compatible with HIPS, and TPU Flex Filament, Glass, PEI, Buildtak, Kapton, 3D Printing Accessories, Supplies, and Materials

I've been using Magigoo for about 3 months, my printer runs almost non-stop and I can say without reservation, this stuff works splendidly. I've only tested it using PLA, PLA+, and PETG so far. Hopefully it will work just as well with TPU and ABS. A couple of things I've learned along the way: 1. Be careful you don't squeeze the bottle too much, or the applicator cap will pop off the bottle and you'll have this stuff everywhere. I shake the bottle really well, place the applicator on the bedplate and push gently to get the goo to flow to the pad on the tip. You only need to do this occasionally as a little goes a long way. If necessary I will GENTLY squeeze the bottle, but only if the applicator is firmly against the bedplate. I haven't experienced a bottle blow-out as others have described but I can see how this could easily happen. Use care and you won't have a mess on your hands! 2. At first I was cleaning the surface with warm water after every print, but it wasted a lot of product. Start with a clean, dry bedplate, wipe it down with isopropyl alcohol (optionally, just makes sure the surface is oil-free), and apply the product in a uniform manner. Don't worry if you have overlaps and bubbles - once the product dries it actually aids adhesion and won't make a significant impact on your print. Once I've coated the bedplate for the first time, I'll let it air-dry and then apply a second layer going at right angles to the first, and then kick on the bed heater to set the product well. 3. WAIT FOR THE BEDPLATE TO COOL DOWN before you remove the print! I wait for the plate to cool to at least 40 degrees C before prying the print from the plate. This will make it much easier to remove the print and it lessens the "damage" to the adhesive's layer. Some of the product will adhere to the printed parts, this washes off with warm water without problems. 4. I use a razorblade scraper to gently pry the printed parts from the plate, trying not to scrape the adhesive off the plate as much as possible. You will see marks on the plate where the print came off - this is great because it means the adhesive worked! 5. I spot touch-up the marks from the previous prints, and I've found that multiple layers of the product seem to work better and need less touching up over time. You don't need to wait for the bedplate to cool to room temp before reapplying the product in small areas, it just dries more quickly. The main thing is don't be in a hurry to wash the bedplate and reapply - it wastes the product and is not needed. Like I said above, multiple layers work better that just one. I've been printing for days with just touching up spots and it's been holding my parts to the plate like a lioness holding her cubs :-) I like this product because it's relatively inexpensive, it has no odor (not to me anyway), it's easy to apply and touch up, and washes off the bedplate and printed parts with warm water. On one occasion, the printed part was a large, flat plate and in that case I removed the print in the sink with warm water. It was stuck so well I was afraid I'd break the print or the glass bedplate, but under a little warm water the print just slid right off. If you use these techniques I've discovered that one small bottle with last for quite a while.

I've been 3D printing quite a while and tried pretty much everything to get prints to stick to the bed. Blue painters tape, Kapton Tape, Hairspray, Glue stick, Acrylic, Buildtak, Clean Glass. For the most part that all work to some degree. Blue tape works, but it wears off after a couple of prints and hopefully you don't press to hard into the tape and it just becomes part of your print. Kapton Tape, I don't think I ever got this to work. Glue stick, works, sort of. Parts stick kind of, and when it cools, they still stick, it's glue. Acrylic, umm. It melts and warps eventually. But you can print on it for a bit, careful don't get the nozzle too close! Hairspray, parts stick, for maybe 1 or 2 prints, and they still stick when it's cool. Hopefully you didn't put too much on or spray the rest of your printer too. Buildtak, pretty much a waste of whatever it is. Parts would stick to it and become one with it. Unless you just barely drop the filament onto the stuff, in which case you get a rats nest for a first layer. Clean Glass, has been the winner for me. So normally when I print on clean bare glass, I have to clean it and make sure the bed is perfectly level. I mean perfectly level. So I have to do this pretty much every print, maybe every other one. PLA sticks at 55C and float off when below 40C. Until you want to print with ABS or PETG. PETG Still sticks really well to the bare glass at 80C, sometimes it sticks so well the glass comes off with the part! ABS I don't print really. But I'm pretty sure it won't stick well without an enclosed chamber and 100 other conditions. That's where Magigoo comes in. Parts stick like buildtak when it's hot, and nearly float off when below 30C. With the Magigoo, I've been able to put an even layer on and launch about 5-10 prints without touching the bed. This, is kind of a game changer. This makes me a bit lazy, but is another piece of the puzzle to being able to launch prints remotely and knock the print off with the nozzle when it's done. Also, parts that have a very small footprint, I would normally use a raft and support, with Magigoo it's really not needed. Probably save $5-10 in extra filament right there. The fact that it lasts more than 5 prints per application, that's pretty huge. Then it's going to extend the life of your glass as well. How much is that worth? This will give you plenty of prints for less than $20 in Magigoo. I think it's totally worth it. Is it hard to apply to the bed? I think it's hard to re-print a part a few times because the print isn't printing perfect in the first few layers. And what if you're not there? How you going to clean off that little bit?

First, let me start by saying the reviewers who complained about the cap coming off likely didn't read the instructions. Underneath the sponge applicator there's a "nib" that when you press the applicator down on your build plate, releases the product into the sponge and while pressed firmly on the build plate you can then slightly squeeze the bottle to dispense the product. If you don't do it this way then it probably will come off. That being said, I can tell you this stuff works awesome, at least for me. I have an FLSUN Q5 which has the lattice glass build plate. Before Magigoo when I was printing PLA, I didn't have any problem with the filament sticking to the plate, which I run at 60˚c, but removing the print even after the plate cooled down I ususally had to use a razor blade scraper to at least get under the edge of the print and then I could use a plastic scraper to slide under and remove the print with no difficulty. NO MORE! With Magigoo applied to the build plate, after it cools down it's literally just a matter of reaching over and lifting the print off the build plate, no razor, no scraper, just pick it up. Might take a tiny bit of twisting just to break the grip, but that's it. Before Magigoo with PTEG, I couldn't get a print to stick to the bare plate so it became blue painters tape and a glue stick. It worked and wasn't too difficult to remove, if for no reason other than I could pull up the painters tape and the print had no choice but to come, but what a pain just putting down the tape. The attached picture (articulated snake) is a PETG print and about 80cm long when straightened out. You can see it takes up almost the whole build plate. I've read some horror stories about trying to get PETG to release from glass plates and taking some of the glass with them but when the plate cooled down, this print released even easier than the PLA prints I did before hand. I just reached over and picked up the head and everything else followed. The instructions say you can put it on hot, I haven't tried that. I just put it on when cool and then heat things up and print. And this stuff literally cleans up with a paper towel just dampened with water and you can see in the second picture the plate is in perfect condition. The couple of little marks you can see are probably from me using the razor blade before Magigoo. I ONLY have experience using Magigoo on a lattice glass build plate so I can't comment on any other combination but for this, it's awesome. And while it's certainly more expensive than a glue stick, just the ease of the whole process makes it worth the money for me.

Magigoo works exactly as advertised. It provides strong adhesion during printing but releases cleanly once the bed cools. I’ve used it with PLA, PETG, and TPU on glass and PEI surfaces, and it performs consistently. A little goes a long way, so the bottle lasts. only issue I had was applying the glue from the stick as it would not evenly release.

Worked extremely well! Solved my problem of over adherence with PETG. Applies very nicely and dries fast. To me it doesnt smell. Simple to use, push down a few times to prime it then spread it, I do pass one direction than another in a cross pattern for 2 coats but idk if this is needed.

This stuff is incredible!!! Just got into 3d printing with a little Ender 3 and had trouble getting my prints to stick, especially to the glass plate. I switched back to the original plate since it’s more of a rough surface and it did okay once I got it leveled but anything longer than 4” or so would warp and one end would always come off the bed, even when printing on a raft! With this Magigoo, everything stays stuck nice and firm to the bed! It makes it a little more difficult to peel it off once it’s done but if you let the bed cool down it’s not too bad. It usually leaves marks on the bed where you can clearly see some of the glue has come off so all I do is re apply some glue in those areas, it’s drys quickly then it’s good to go for the next print. I don’t clean it all off between prints. I just wipe it to make sure the dust is off. Would HIGHLY recommend and will definitely be buying again. Saves me money in filament since I was having to print everything on rafts before just to get them to stick. Now I just brim & skirt. The orange print is with Magigoo and the grey print is without Magigoo and it was printed on a Raft trying to get adequate adhesion but obviously it didn’t work.

So far (about 7 printed plates in) this is working very well. I got tired of the goopy-glue stick like glues leaving a mess on the product. This applies easy, smooth, and clean. It is more expensive than other options. But I'll pay a little more for less stress all day long. I will buy again.

(((2026 update, I changed my review from 1 start to five, because I ordered this over a year ago and I used it on textured plates only and it doesnt work good on those the texture tears up the pad on the end of glue stick fast and doesnt stick well, but for glass print plates and smooth pei plates , specially glass print plates this stuff is freakin awesome, magic, and when a print is done just spray a little alcohol towards bottom of print and the prints slide right off, you can hear it just loosening up, I love it, annnnd I ordered just 1 tube over a year ago and its still more than half full, thats crazy, ive printed so many things from huge to small, should last atleast 2 more years. I definitely recommend this and apologize for my negative review in the beginning...)))This stuff here 🤦🏽‍♂️before I purchased this stuff I've NEVER had a print come loose from the printing plate, already ruined 3 prints wasting Hella hours and filament and all I get is a little refund and a trip to UPS, definitely not for big prints or even small prints,ruined a rocket I printed 🤦🏽‍♂️like 30 minute's in, the stuff feels sticky until the bed warms up then it evaporates leaving a smooth surface, the prints slide right off when done, that's no good, I'll never buy this junk again... Do what you want tho, I thought those stuff was good Givin the price but NOPE!

Quality is good

I was skeptical when I ordered this product. "Is it just a big expensive pritt-stick?", I thought. Having used the product, now I'm a believer. I'm using it to print PLA onto a glass surface. The first layer sticks very well, with no smearing or dragging of the first layer. Mission accomplished! However I then discovered the product has a second benefit which I didn't anticipate: once my heated bed cools down the print separates from the bed effortlessly. I can retire the putty knife I used previously to pry prints off the bed! So basically it's all brilliant on that front. The magigoo seems to remain on the glass, it doesn't transfer to the printed part as glue stick sometimes does, I've done about dozen prints without any need to re-coat the bed. Hopefully as long as I store the product properly (in the dark, it seems) it will last me a long time. I've only tried printing PLA so far. I'm going to try experimenting with PETG next. The only downside to the product is that if you have an uneven coating on magigoo a glass bed, which is what I ended up with having used the applicator they supply it in, any ripples or texture in the coating are transferred onto the printed part. If the bottom surface of the part will be on display this leaves an uneven pattern reflective/matt texture on that surface of the part. The best solution I have found so far is to lightly sand the surface with 1000, 1500 and then 2000 grit sandpaper after printing to give an evenly matt texture. Overall I think this stuff is great, not having to worry about adhesion or removing the print from the bed has made printing much more fun and practical. I bought this concerned that it wouldn't prove good value for money -- I'm pleased to report that I was wrong!

Uso questa colla per il piano di stampa ormai da anni e mi sono sempre trovato molto bene. Aiuta parecchio con l’adesione ed il distacco del primo layer, soprattutto con quei materiali o quei pezzi che tendono più facilmente a sollevarsi dagli angoli. La cosa che apprezzo è che è semplice da applicare grazie alla spugnetta e non serve esagerare con la quantità: basta uno strato leggero e uniforme sul piano. Nel mio caso si è dimostrata affidabile nel tempo e continuo ancora oggi ad utilizzarla. Per chi stampa spesso in 3D è uno di quei prodotti semplici ma molto comodi da avere sempre vicino alla stampante.

Magigooは凄い。 よく張り付いて、モデルが歪みません。

Ich war ein wenig verzweifelt. Ich habe den Artillery Sidewinder X1 V5, der ja schon von Haus aus ein sehr gut haftendes Druckbett hat. Ich habe mich vor etwa einer Woche an das Drucken von ASA herangewagt. Da ich (Noch) keinen gekapselten Bauraum habe, hatte ich mich schon auf Haftungsprobleme eingestellt. Und so war es dann auch. alles was höher als 10mm war löste sich früher oder später von der Platte. Dann habe ich diesen Klebestift bestellt... zu verwenden ist er etwa so wie ein normaler Klebestift die Konsistenz ist bei kalter Druckplatte etwas dicker als Wasser. so kann der Kleber schön in alle Unebenheiten der Druckplatte fließen. sobald ich dann die Platte heize fängt der Kleber an zu kleben. nach dem Druck bekomme ich gedruckte ASA-Teile nun nicht mehr von der noch warmen platte gelöst, vorher lagen die Teile halt mehr oder weniger auf der Platte. sobald die Platte abkühlt hört man schon wie sich die Teile selbst lösen (knackt und knistert). anschließend nehme ich ein stück Nasse Küchenrolle und reibe kurz über die Platte. Der Kleber ist Wasserlöslich, daher ist die Druckplatte danach blitzsauber. das entfetten mit Spiritus lasse ich mir aber trotzdem nicht nehmen. leider finde ich 18€ etwas viel, aber verkraftbar. zudem weiß ich auch noch nicht wie ergiebig so ein Stick ist. Alles in allem klare Kaufempfehlung von mir. ich werde gar nicht erst irgendwas anderes auprobieren, da diese Anwendung sehr einfach ist und ich hinterher kein geschmiere habe.