HVLP Spray Gun Kit, Automotive Paint Spray Paint Gun with 3 Nozzles 1.4 mm 1.7 mm 2.0 mm, 600cc Cup and Cup Systerm Connector, Air Spray Gun Automotive Paint Sprayer for Car, Fence, Furniture(Green)

Buen precio excelente lo recomiendo

Bought this because it comes with 4 sizes of needles and nozzles. The Harbor Freight stuff usually has only 1, maybe 2 needles and nozzles, and getting more in different sizes is impossible as far as I can tell. The other deciding factor in my purchase was that it comes with a 2.5 needle and nozzle - and I wanted to try using it to spray house paint. Which it did fairly well. Needed to thin the paint a bit and run max pressure to the gun, but it did spray. Was also able to test the fan spray adjustment. Even with house paint I could go from a decent fan down to a round spot spray. Not a show room car finish, but I wasn't painting a car. Few thoughts on the gun. First, it comes with 4 needle / nozzle options. 3 sets in bags, 1 already installed in the gun. Problem is, they use glue or locktite when they installed the nozzle. Why on earth would you do that on a part that is supposed to be removable ????? Have read other reviews that mentioned the same problem with this and other guns. Seems really stupid. One reviewer mentioned using a heat gun to soften the glue to get the pre-installed nozzle out. After clamping the gun in a vise and using a hammer on the supplied wrench - literally deforming the wrench - and getting nowhere, I tried the heat gun. Fortunately that worked, and I don't think it damaged the gun, although some of the paint in the nozzle area did come off. Serious aggravation that didn't need to happen. Cleaned it and installed the 2.5 nozzle and needle. Also of note, if you use the original 3M pps cup system, the adapter #2 fits this gun. With my 3m pps system, I have created a custom pressurized cup system. It bleeds a little air off my line and puts pressure on the outside of the cup liner to help force heavier paint into the air stream. Works great. You can get a 3m pressurized cup system, but they only come in large and small cup sizes, not the standard cup size. So I made my own. I mention this, because I can't say if the gun would have sprayed house paint from a purely gravity fed cup, as I didn't try. But I suspect it might, just not as well as with a pressurized cup. Also of note, the included cup does not have a securely attached lid, or even a sealed lid. One would have to be careful not to tip the gun too far to avoid the lid falling off and spilling paint. Another gripe is that the needles and nozzles have no size markings. Only the air caps have a size stamp. So if you toss them loose into a drawer, you're going to have to figure out which needle goes with which nozzle. So, no size markings on needles and nozzles, no way to keep the supplied cup lid from falling off, and a glued in nozzle from the factory - all mildly annoying, but not deal breakers for me. The gun itself seems to be decent quality for the price - at least Harbor Freight level, maybe a little bit nicer. And you get 4 needle size options included - something that is usually an extra charge, if you can even get them. I have not used it with automotive paint, so I can't comment on that. But I do plan to use it next time I shoot automotive primer, and I see no reason why it wouldn't work. As a final note, this brand also makes cups and liners that are exact copies of the 3M pps system. However the disposable liners are stiffer than the 3M product and do not collapse as readily when spraying. That actually causes problems when spraying - enough that I plan on sticking with the 3M brand. My review on those will be posted soon. But for the money and the multiple needles and nozzles, I would buy this again. It seems to do a decent job and gives you options for various thicknesses of paint / finishes

I bought this because it is a complete package. Gun needles for every stage of project and enough strainers to complete a job. When set properly for the fluid viscosity. It will perform just as good as a more expensive sprayer. I compared the tips, air caps, and air flow holes. They are all about the same.The differences are materials of construction that changes price. But the difference of finished results summed up by preparation, technic and products used. Just be certain to properly clean between fluid transitions.

I had high hopes for this spray gun, so much for wishful thinking. Here's my observations on this gun.1.) The fan control knob is held on with a screw that just doesn't stay tight and wobbles from side to side.2.) Under the fan control knob is what's left of the o-ring sealing this mess. It's torn and shredded. No point in even hooking this up to air.3.) The fluid control knob: I backed it out and fully expected it to be stripped, that's what it felt like. The thread tops had areas gone from improper thread cutting.4.) The lock nut for the fluid control: There should be a machined land (area) on the gun body for the lock to tighten on top of. This lock is essentially cocked to the body and only tightens where it jams into a small part of the casting. When you adjust the fluid control the lock is just a repeatable aggravation to deal with.5.) The cup has numerous scratches, dents and dings. Frankly, I couldn't care less but it just shows the lack of caring with everything about this gun.I bought this because it had 4 needles of various sizes I could use. Sadly though the gun itself won't support the needles sets so back it goes.I wound up buying a gun from "The Gelcoater" because I just can't find a quality gun on Amazon. The Chinese do some things well, like their marketing page, but this gun is a loser.

Works okay for the price, you get what you pay for. However to change the tip to a bigger size was extremely difficult it was stuck. The tip is just supposed to unscrew, but the whole thing came unscrewed and I had to use a allen wrench to get it out. Once I got the new tip in, it does function and work okay for the price.

Bought to spray metal flake in clear works great love that it’s 4 guns in one sprays very even

Worked great first 2 weeks, then just quit atomizing. Company replaced gun works fine now

Haven't used it yet but seems like it's good quality, wouldn't paint a car with it but for small projects I think it's well worth the price, wish it came with instructions that are geared for the first time user like me.

Came with a broken lid,also does not fit either one of my guns with 1.0 disposable gun adapters. Disposable cup lids will not go in far enough to lock.

Buenas

Looked great to have multiple nozzle sizes and was the main reason for this purchase. The gun comes with the 1.4mm nozzle Loctited into it, and once it’s removed you discover that the other 3 nozzles have not been finish machined and therefore don’t fit into the thread. The instruction manual also contains a drawing of a completely different gun. I agree with other reviewers that the lid on the paint pot is pathetic.

Me sirvió una semana primero empezó con el gatillo después el abanico ya al final dejo de funcionar