BRISStainless Steel Boat Launching Dolly for Inflatable with 16” Wheels Hand Trailer

Easy to assemble - easy to use. I cut the long rod 18 inches short [to 14", 6"] and re-drilled connect holes to fit smaller 7 foot inflatable with a small gas motor. [was super easy to do]. I pull my boat from my backyard across the street and down to the neighborhood beach to launch right off the trailer into there water. It is light and easy to put in and take out. Wheels are excellent. High recommend.

Not for inflatable boats!!!!It is quite easy to put together. It takes less than 5 minutes to assemble or disassemble all of the pieces. When disassembled, It takes small amount of space.Bad design: Almost the entire weight of the inflatable boat is supported by the mere edges of the 4 stands. Since the inflatable's bottom is not rigged or hard, the grey rubber line you see in the picture that runs between the each stand does not lift the boat up. Consequently, the entire weight of the boat sits on these tiny surface area of the edges of the metal stands covered by the rubber material. When the boat sits on these 4 corners, it looks as if the boat's pantoons on each sides are poked by these edges.In reality, the inflatable boat should rest on the rubber lines and not on the edges of the support system. Hence, the distance between each side of the metal support should be about the size of the outer width or beam of the inflatable. In my case, it is almost a foot less then the outer with of the boat.I have a mercury inflatable 13' 9", 250lbs. The transom sitts about 1-2 feet away from the rubber support system. Since the transom is the heaviest part of the inflatable, it has to sit on the rubber line. However, if you line up transom with the rubber lining of the trailer, the bow sticks out. Basically it is at least 2-3 feet short for 12-13 feet boats. In other words, do not consider this if your boat is more than 10.5-11 feet longGetting out of the Water: it took one adult and 2 kids to to get the boat out off the water from the boat launch ramp, due to its incline. At 260 pounds, it is quite heavy for one person to pull it alone (I'm a big guy and couldn't do it alone. However, the difficulty is dependent on how steep the angle of the incline stands.Outting boat on trailer: Inflatable boats that has hard floorboards, need their floors installed on a flat surface. In other words, you have to lift up your boat on to the trailer after all floorboards are installed. The weight of the floorboards, increase the weight of the boat significantly.I found that it's is nearly impossible for me to do this, without significant amount of heavy-duty lifting effort and struggle on my behalf, due to the solid weight of the inflatable.

This hand-operable trailer was a good fit for 14' 200 inflatable boat/raft. It was easy to assemble and good quality. My only complaints are 1) there was no option to tilt the handle up or down which would have been a nice feature. I ended up modifying the handle to keep it straight and this gave me more leverage to lift the boat as I was rolling it; and 2) a front wheel under the that handle bar would have been a great feature as well. As it is, a heavy boat/raft is difficult for one person. Having to keep it lifted up enough to roll on its back wheels with a 200 lb. inflatable is quite a challenge.

Great product but i wish the bolts and nut were standard not fly nuts , also the steal could be a little thicker gauge metal. I love the design it’s easy to use I converted it so i could pull it with my 4 wheeler....

Is a perfect fit for a sunfish sailboat. Easy to put together! Did all the research and just needed a basic dolley. So happy I found this for a great price.

This is a strange product to review. It is actually really sturdy and made with extremely hard stainless steel (high chromium content), but it shows being assembled with pins and actually came with wingnuts instead. The first time I took it out the dolly floated and I couldn't get it under the boat. The pneumatic tires float. I spent $65 on different wheels with solid tires to solve the problem. Very poor design. Not thought it at all.

The square tubes are engineering terribly. There is too much gap between them and they don't lock (or hold weight). Company provided zero customer service or solution. Product would be fine if it was designed and manufactured with any quality at all.

Works perfectly for what I need. Great Value