Rust-Oleum Tub & Tile Touch-Up 2-Step Kit

Works as advertised, and makes a good hard repair. Two caveats: 1- the instructions really mean it when it says to use in 24 hours. Hardens like a rock after that. 2- not all whites are the same. If you’re lucky it will be a perfect match, but in my case was just a little “off”. That said, the goal was to repair a bad chip, and it was close enough.

I had a bathtub that had a lot of wear on it, and my landlord was able to repaint it and make it look nicer. Unfortunately minor cracks would pop up after 6-9 months, and as a preventative measure I picked up this kit to patch those up. It seems to do the trick and covers up the cracked spots well, preventing further splitting. The color is fairly close though I don't really mind that as much as I'm renting and the bathtub isn't perfect to begin with. The paint definitely smells so I would recommend running an air purifier in the bathroom for about 24 hours after application. The only downside is that it totally dries up after about 24-36 hours so you only get a few applications.

Overall, I was happy with this product because it was one of the only products that I could find that was inexpensive and would do what I needed. I was looking for some type of paint for my enamel bath that would be waterproof . Previously, I had chips and dings in my bathtub and mistakenly used JB water weld putty stick to repair, however the product stated it dried off white but it did not. Instead it dried gray/purple so then I had a lot of gray marks all over the tub which wasn’t better than my chips. I have been searching and searching to find something to basically paint over the JB water weld. They have plenty of kits out on the market that are very expensive and a lot of kits on Amazon that I was a bit leery to use I needed to be sure that whatever I used would be completely water. . I found a few videos where someone had used the tub and tile specialty paint epoxy, by Rustoleum and since I was familiar with the namebrand and it seemed fairly easy., I decided to give it a try. There are a few things I would like to mention that may be important: 1. The smell is very strong so wear a facemask and hopefully shut the door and blow some fans directed at the window to get it out as soon as possible.. The second thing I would like to mention, (I saw some questions about this) , and that was whether this would work on scratches. It does not unless you sand it first and then put some type of filler down before painting. I tried painting over some scratches in my bathtub and it did not work. Also, be sure to really sand down anything that you will be painting over (ie the JB water weld I used). .. I unfortunately did not sand it down enough so that it was flush with the tub so there are raised bumps in the tub that are now painted white, . That’s fine with me because eventually I will have to refinish the whole tub.. I got the product today and applied it, so I am not able to give feedback on whether it is waterproof, durable or if there are any issues. I will say that it was quite easy to apply and my recommendation would be to layer the coats if you need more than one Radan applying a thick gob in the beginning. One other thing I would like to mention is that I thought it would drip more than what it did so I put a lot of painters tape around the area as I was painting, which I did not need to do Another thing I didn’t realize was that it takes three days to fully cure and I unfortunately did not see that until after it has completely dried and cured and will update as needed.

As everybody says, it’s bright white which wasn’t a true match, but since most of the areas I wanted to cover were small head-of-a-pin-sized holes it filled the holes neatly and they become invisible unless you know exactly where to look. The directions say to recoat after 10 minutes — I found that was too soon and got better results after 20 minutes. I found the brush in the cap too big for my use — wanted to just fill the dings, not coat the area around them — and found a toothpick was a much better, more precise application tool. It is also very runny immediately after mixing, which is fine for flat, horizontal surfaces. I had a few vertical surfaces and got better results when I’d let the paint sit for 15+ hours, with very little running because the paint thickens the longer it sits after mixing. By 24 hrs it was very thick and time to throw out what wasn’t used. An inexpensive solution that worked great.

there should be a better way to apply this maybe a sponge but the little nail brush would be OK for those who do their nails. As for the paint it seems to work OK but the existing color showed through at first but when dried it was gone, maybe it leveled out?

This product worked well to cover up the area around my drain that was starting to rust. you can tell that the area has the paint on it but it looks 10x better then it did before. It will not make your tube look like new but is defiantly worth a try if you are just trying to fix a small issue. My only suggestion is to make sure you not only clean the area but to sand the rust areas really good before applying if that is the issue for you. i thought i had gotten all the rust off from one area but did not and now the rust is showing through the white paint so i will need to remove the paint and fix the rust issue then redo it.

Lasted for less than 2 weeks. Followed the instructions perfectly. This is a bogus product, don't waste your hard-earned money on this.

Did not fit my bolts. Not any fault of the sellers. I think the installers jack legged the toilet bowl to the floor. Refunding for refund. No problem with the seller

One of the bottles arrived almost empty. The liquid was poured on the package. Waste of money.

EDIT almost three months later looks the same and the patch has held in a 5-person household with shower running daily and baths with bubbles weekly. Tub was reglazed when we bought home. 10 years later it needs to be redone. We plan to redo the space but wanted a tie over until we do. Was looking for simple and cost effective. I used all the paint and did three thin coats. Best tip, use your own brush. Better tip, fresh brush for each coat as I definitely have some brush hairs stuck in there. I wore an N95 and opened windows with an air-purifier running. Smell is gone after 12 hours. Hardest part was drying the tub and prepping as it is our only showering space. I would highly recommend this for a practical fix. If you are looking for aesthetic get a pro. Pics are of 12 hours after treatment and after prep work. I chipped the damage back in hopes of better sealing and the work lasting longer. We plan to put a bath mat over top (which caused the damage in the first place). I wanted to write a review because the reviews and a YouTube video showing how to use the product really helped me.

This is one of those must have products that can save you hundreds but unfortunately becoming impossible to find. Absolutely recommend. Even if it's not a perfect colour match for a cheaper tub, it was for my taps and the job on the bathtub looks a million times better than a black chip mark. Everything is still intact with no flaking or peeling. 100% recommend

I had a bathtub caddy that scratched my tub that I had previously painted. This was very easy to use for a small repair such as that and it matches pretty much perfectly. It is expensive for the little amount you get but if you just need to touch up a small scratch I think it’s worth it compared to the hassle of refinishing a whole tub again.

I thought this product was supposed to fill in cracks and chips in tiles, but it is basically just a paint (but worse because after 24 hours you can no longer use the product). Even after multiple coats it doesn't fill in the damaged areas (see pic).