BIGTREETECH SKR Pico V1.0 Controller Board Perfectly Compatible with Voron V0.1 3D Printer, Fits for Raspberry-Pi Using Klipper Firmware, Entry-Level 4-axis DIY Motherboard

I have 3 of these in custom built delta style 3D printers, so they are not just for Vorons. The small size is perfect and I like that you can stack a Raspberry Pi under or on top. I use these with a Pi zero 2w stacked on top with a cooling fan and have had no issues. This would be my go-to for any basic 3D printer upgrade to Klipper, along with a Raspberry Pi Zero 2w.

Massive upgrade from MKS SBase board to this on Tronxy X5S, allows use of klipper and layout makes setup very easy.

Nunca la pude conectar directamente a la raspberry por UART y la placa tiene un problema con la conexion usb que ya ha sido ampliamente documentado, pierde la conexion facimente, durante un tiempo funciono, pero de un momento a otro empeso ese fallo de USB que nunca supe que era, funciono un rato precionando el boton de reset al iniciar, pero me aburri y el deje de pisapapeles, se que es funcional pero no tengo tanta pasciencia 😅

This board is perfect for smaller printers. I'm using it in a custom build with klipper. The footprint matches a pi and the board can also power a pi and communicate with it directly. No USB or external power supply needed. The sideways connectors prevent stress and keep things tidy. Very cool!

For openers, I've been designing and building 3D printers for almost 4 years now... Some Marlin... mostly Klipper. I've had my share of controller boards, but this one remains the one that burned 2 weeks of my time and I couldn't even get it to turn a stepper motor! Add that to the 9 days I waited for a not-very-helpful response from their tech support, and then another 8 days after I immediately responded. Documentation is typical BTT (mostly on Github, and with errors... i.e., the picture of the Pico has the JST connector going into the Dupont, and vice versa). I can only conclude this board has problems, and they probably know about it... so don't expect a response. I'm now 3 days away from the return window so its going back... My advice is to go with a more established board. As nice as this board looks, you'll burn a few weeks pulling your hair out.

Just got this this morning haven’t installed it yet but I love that the pin out is on the back of the box

Have it hooked up using uart very responsive and works great.

My SKR Pico for my Voron V0 just randomly died only a short 4 months after "upgrading" from my SKR 1.2 board. It didn't even have 100 hours of print time on it. The Picos are full of all sorts of issues, just do some Googling to see all the problems with it, including issues with connecting to the MCU, issues with the USB power, issues with the serial connection, and more. I would wait for an updated board if you can. Unfortunately, I have to order a second one of these as I need to get printing, but I really would not recommend this thing as it is now.

This can be used for so much more than 3d printing as it took me some time but have been able to use this for a lot of Pico builds (robotic arm) and it has the tmc2209 stepper drivers builtin. Micropython works great.

amazing board, no issues and worked great for my voron 0.1 running klipper.

revived a bad board the y axis sensor wont work on sensorless or with a sensor tried both so I cant home the printer. all other axis behave as they should an home np.

Nothing negative to say for a klipper setup it is recommended italso a small format

Never could make one work. I tried 2, every print failed for no specific error. Best i could tell the were disconnecting from the pi mid print. Changed to 2 other boards and both worked perfectly with the hardware so i either got a bad batch (2 of them) or the boards are just no good