Grafix Computer Adhesive Backed Ink Jet Film – Self-Stick Printable Film for Creating Custom Journals, Stickers, Photos, Jewelry and More, Ink Jet Printers Only 8.5 x 11”, Clear, Pack of 6

I use this product for custom foils for card games. Be aware that adhesive isn't totally clear. Attached is a comparison of this product (left) vs. a laser printed foil attached with glue (right); as observable, this product produces much more vibrant colors with better, clearer foiling. It's not completely clear, and it won't pass cursory inspection, but it's the best film for foiling. Be aware that, depending on your climate, you may have to let it dry for much longer than I did (i gave it about 10-15 minutes). The adhesive is strong and sticks; I just wish it was slightly cheaper, as 70 smackaroos for 50 pages is rough. Use a boxknife or a razor knife to separate the adhesive carefully from the backing. Printed with an HP Envy 5055.

Just an awesome product. Bought this to do wording for my 3d printer business. This paper has allowed me to one up some of my competitors. My only complaint would be it is thick. I would love it a few mils thinner but other wise works great. Drytime is not an issue. Print on it, put it on a self for 10 minutes and dont touch it. Worked great from the first print. I am using a cheap hp ink jet so nothing special on my end to make it work. Will be ordering more. As a side note - If you are using it to make a sticker for a dark background light colors like yellow will not show up. The ink is translucent. Make sure you print bold and in a good font to contrast your surface you are sticking it to.

I purchased this for use in Pinewood Derby cars. The paper worked well and printed clearly on my HP Inkjet printer. The film is quite thin and is translucent. It stuck very well to the cars. Others have mentioned a lack of clarity. I did not find that and was happy with it. One word of warning is that it takes a while to dry after printing. I touched it too soon afterwards and some of the graphics smudged. I would recommend that you give it 12-24 hours prior to aggressively handling the printed output.

Terrific product except when trying to apply it to a transparent plexiglass sheet. It is extremely difficult to apply without bubbles. If there is any speck of dust on the plexiglass, it shows dramatically in the transparency of the image. The company was very understanding of the problem and tried to help by offering suggestions as how best to apply. I learned that if you lay the sheet on one corner of the plexiglass plate and using a paint roller, push gently against the film as you roll it down onto the plexiglass, you do not get bubbles. You have to clean the plexiglass completely and be sure there is not a speck of dust remaining on the surface. If all goes well you have an amazing image and translucent-which is worth the effort!

Nice clear printable paper. It is a bit thicker than I was expecting. Which actually ended up working out based on the project I was using it for. The inject prints out a very nice image onto this. However, you absolutely will have to put some form of clear coat or laminate on it or the ink will rub off or run. I used an acrylic spray. As I mentioned, this is thicker material. So not for use on something that you need bend-ability or flexibility on. And because of the thickness, the outer edge of where you cut out will be noticeable wherever you stick this down.

this adhesive film works great for what I use it for. I bought this because I make my own decals for RC aircraft. I have no problems using this with my canon inkjet printer the ink drys fairly quick 5 min or so not a big deal for me and does not smear. I might have to see if I can set printer to put down less ink just to see how that works. the only problems is that its hard to remove the backing the easiest way is to take two pieces of tape and put on both sides on the corners of paper and pull apart. works like a charm I will buy this again.

Excelente

This is a fantastic product for making titles and graphics for your scrapbook. It allows the background to show as if the title is floating on the page. The adhesive makes it easy to adhere to the page. By using the landscape feature you can create titles that go across 12 x 12 paper. I would definitely purchase this product again and highly recommend it. I also bought Wausau Papers Astrobrights Print and Stick which has a matte finish and adhesive back on a bright white paper for titles and graphics.

Awesome product.did what it said it would do .printed nice color dried fast and applied super easy. Great product .pricey but worth it .

El papel de buena calidad

I love these, I use them to make altered art foil MTG cards for EDH decks. Saves you a butt load of money and most times they look better than the real thing

Really nice quality was impressed. In the beginning, I thought my printer (HP Office Jet) wouldn't pick the paper, but everything went fine.

Bien buena calidad