Tyger AutoTG-FF6D4208 for 2002-2008 Dodge Ram 1500; 2003-2009 Ram 2500 3500 (ONLY Fit 8' Truck Bed) | Paintable Fine-Textured Matte Black Factory Style Fender Flare Set, 4 Piece

Been looking at trucks for my stepson for months. I live in CT so nearly everything we found was rusted and rotted. Found a nice 2004 Dodge Ram 1500 with a perfect frame and bed crossmembers. But... it had the typical rear fender rot. My picture shows the worst side, the passenger side. These are about 4" high so it covered the rot up well! My stepson did the installation himself, and he is a novice wrencher. I feel like anyone can do this!! He did mention the top screw on both back fenders needed to be drilled, but also said they are very secure as it was. I will end up drilling those holes for him later. I highly recommend this set of flares, especially if you're looking for an OEM look, and not those gaudy, ugly flares that have the visible screw holes on the top of the flares. those are horrible looking.

These flares are fantastic. Easy install, with provided hardware, and I think they look great! They provided enough coverage to hide the "fender rot" on my 03 Dodge Ram. I sanded down the areas, and gave them a good coat of Rust-Oleum first. I installed these alone, in well under an hour. I did drill one hole on each rear to help tighten them up a little, but all other screws went in the factory holes. No rubber seal was provided, but they fit well without it.

They look good and install was very easy, some reviews complain about not fitting well, fits mine very well. I altered the install slightly because i have large mud flaps that fit over these flairs. I had to remove the cummins emblem on both front flairs, decided to leave them off. I also had a repaired rust area i was trying to hide, typical rust over rear wheel arch.

Pretty easy install. A couple of hours. Didn't need to remove tires or HEMI logo on my '06 Ram. Fit is acceptable with a few small gaps. Supplied instructions could be better. One step said drill a 1/5 hole which I tool to mean .200". I actually used a 1/4" bit with no problem since that was the size of holes that was already in the fender well. Didn't even need to drill any holes to install front covers. Covers up the start of some rust on the rear wheel well. Looks good too!

I love these fender flares! I wish I I’d found them years ago, I have had bedrust for years and never found flares I liked, most stick out to far. But I liked these, and the price. Decent construction, holes were lined up, with the option to add more. Maybe this will keep some water off the damaged bedside underneath and make it last just alittle longer...Note: you do have to remove your Hemi badges. There is also NOT a gasket around the flare, doesn’t bother me, but might bother someone that plans on taking them off one day?? I would imagine over time it will mess the paint up very slightly from not having a gasket. But it’s not a worry for me.

Well, newer anyway! Worked great covering up some questionable rust bodywork (by me). On the 2006 the holes were spot on. Only had to drill a couple of spots to let a extra screw I used go through the wheel liner. Mine had Dodge mud flaps that needed to come off (as mentioned on the page) but I probably could have adapted them or the arches if I wanted to. Went too long on the right side rear so the rust was higher, but still covered most and if I make a better repair it will be really nice. A solid 15 footer which is all I wanted for this low mileage work truck. Took maybe 15 minutes per wheel, leaving the tires on and not in a hurry.

These are nice flares! There price very reasonable. There easy to install and they conform to the bottom panels great! I like the fact that they come with a complete new replacement hardware kit. The hardware kit is an exact replacement of what came off. They give my truck a real good look. A trim package. Highly recommend these flares. Somebody spent the time to get there mold right. Well worth the money spent

Ordered these after trying out another brand. They fit ok, better than the last set, but not an oem fit. Prepped and finished these with duplicolor perfect match. Looks ok for a 2008 truck. Was missing some speed nuts. Had the dreaded dodge Ram rust. Pulled the taillights and treated the inside out of the bed with POR15. All in, like $200. Cheaper than a new bedside.

Had the shop doing the out of province inspection on my truck install these fender flares.They fit perfectly, look awesome and the mechanic told me they were a quick and easy install. I really like the low profile, close to the body, shape of these fender flares.

Exelente le quedaron a la camioneta

I installed these on my 2004 ram because the box had rust on the wheel wells and wanted to improve how it looked. They installed easily (I just used self tapping screws) my only issue is that the very front of fender has “Hemi” badges that interfere with the fit, so should be removed before installing in my opinion.

Fender flares were easy to install and covered all the visible rust around the wheel wells on our truck. They fit well and look good. We used some car door edge trim to finish the edge that goes next to the truck. It looks great and will stop any rubbing on the painted surface and seal the edge better. This kit could use more u clips and also should come with the door edge trim for a few dollars more. Very Happy with this purchase.

So easy to install. Less than 45 minutes to install all 4 pieces!!!!!! Looks great. Fit was decent