LimbSaver Classic Precision-Fit Recoil Pad for Synthetic Stocks

This stock fit perfectly on my Browning A-Bolt 30-06. I already know it is going to calm down the recoil based on other rifles I have this pad on.

Despite the product name, this is the same product as the Limbsaver Precision Fit Recoil Pad, which is printed on the packaging. It is an outstanding product--MUCH softer and more shock absorbing than the pad that comes from the factory on the Mossberg 590a1. I was getting a very mild soreness in my shoulders after putting 50 rounds at a time through my shotgun. It wasn't too bad, but this pad eliminated that. I could probably shoot 75 - 100 rounds now without becoming sore, and the recoil feels more muted. It's not an enormous improvement, but certainly noticeable enough to be a worthwhile upgrade.This part number (#10121) is the SMALLER of the two Mossberg-sized pads that Limbsaver makes. I had a full size synthetic stock, which would normally take the larger pad size. However, I wanted to reduce the length of pull for more comfortable shouldering of the weapon. I cut approximately one inch off the length of the stock in my table saw (using a 60 tpi fine cut blade). That shortened the length of pull nicely and reduced the end dimensions of the stock to 4-7/8" tall x 1-9/16" wide--EXACTLY the size the 10121 pad is designed to fit. Since I had cut off an inch of stock, I had to use an 1/8" drill bit to deepen the upper screw hole in the stock. I also had to drill a new lower hole (about 3/16" lower on the stock end than the factory hole). It worked great. I have a shorter length of pull and a much softer (Limbsaver) pad that fits so closely you would assume it came that way from the factory. If you look very closely at either side, there is about a fingernail's width of overlap where the stock is slightly wider than the pad for about 1-1/2" because the profile of the stock bulges just a bit more than the profile of the pad. It's so slight that even I--a confirmed perfectionist--am still totally pleased with the results.Simply put, it makes the entire shooting experience a little more comfortable.

I put mine on a Ruger M77 MK ii and it fit great, and made shooting a 7mm Rem Mag much more comfortable than it already was. Anyone looking to purchase one of these just make sure you check which rifles the limsaver fits on and if you need an adapter piece there is a number you can call and they will send you one for free!

While not a perfect fit, I was able to install on a CZ Swamp Magnum O/U. The slotted screw holes are maxed out to fit the 3.5" screw spacing on the CZ. The profile is a little undersized in two locations, but not by much. A good option for the CZ Swamp Magnum, as Limbsaver does not make one specifically for this shotgun.

I love these pads, they do a great job. However, limbsaver is getting cheap and or lazy. They do NOT offer any attachment hardware (screws) whatsoever! The screws in the stock pad are stuck in there so tight, it's practically impossible to get them out so need to source new screws. Very disappointing!

Easy to install and was a perfect fit on my Remington SP-10. Looked just like the original.

Great cushion and fit on the Remington 870 tactical.Would buy again or recommend to a friend

Very easy to install, I used the screws from the factory pad. Definitely reduces felt recoil!

I have an Air-Tech version of these on my 300 WIN MAG Tikka T3x, which makes a world of difference. I was afraid that the Classic version wouldn't be nearly as good, but was pleasantly surprised when I put one on a 12 Gauge. It's not quite as effective as the Air-Tech, but still makes a big difference and is leagues ahead of cheap slip-on recoil pads. Made the 12Ga comfortable to shoot, and my shoulder didn't start getting sore until some 20+ rounds of continuous shooting.In case anyone is wondering, the 10008 model will fit a Charles Daly 101 12Ga break-action shotgun. I couldn't find any info online and had to print the templates and compare. You will have to shave a bit of plastic off the inside rim on the recoil pad to get it to fit inside the stock, but once it's on, the pad fits like it's factory.

Awesome recoil pad, replaced the pad on a Benelli M4 which is like a hockey puck.This limbsaver requires a little modification to work on the M4 telescopic stock but it’s quite easy, just google it.Worth the money

These recoil pad fit real nice on Tikka T3X, nicer than on a T3. Just centre in around the edges and you will be really happy when you shoot it next time.

The fitment was good

Great fit , made my tikka 300 win mag kick like a 270 .