Moto Z Force Screen Protector, PLESON [Full Coverage] Motorola Moto Z Force Tempered Glass Screen Protector, 0.26mm/Case Friendly/Bubble Free Screen Protector for Moto Z Force 2016

This screen protector does not stick onto the screen in certain areas, specifically by the earpiece and home/fingerprint scanner button cutouts. It's like the screen protector is not formed/fitted correctly to the Moto Z's screen or the screen protector does not have enough adhesive or is not "sticky" enough in those areas.So my Moto Z Force is brand new, removed the protective film it ships with, at that point the screen is clean and clear since it has not been touched yet. I made sure the screen was really clean by using the cleaning wipes the kit comes with as described in the instructions. I then applied the screen protector and was able to get it perfectly aligned on the first time. I then pressed down on the middle of the screen and watched as the adhesion of the glass screen protector spread out locking down the protector on the touchscreen. There were about 5 places that the screen would not stick to along the edges of the screen protector. Pressing down on the areas would cause the protector to adhere, but after a few seconds would come up or detached in that area. I held down the areas for about 5-10 minutes and three of those areas finally decided to adhere correctly. The two areas that will not adhere at all are by the two cutouts for the earpiece and the home/fingerprint button. Very disappointed in the product as this offers a total coverage of the device's screen. The quality looks to be there, but will not adhere correctly to the screen.

This is the 4th Pleson screen protector I have used, but the first for my new Moto Z Force. Since I am familiar with the Pleson instructions, it was simple for me to install - in fact, Pleson is one of the easier brands to install, in my opinion. However, no matter what I do, I can't seem to get the last few bubbles out around the cutouts. I did try to peel up the corner and re-adhere the glass, but that did not work, and in fact maybe made it just a little worse.I am going to see if my need for perfection will allow me to continue as-is with the bubbles in the screen, but likely I think I will have to order a different brand. I'm so disappointed, as I have had really good experiences with Pleson in the past.

The packaging is excellent in the cutouts are very precise. I bought this specific brand because of the fingerprint sensor cut out. The cut out for the fingerprint sensor is exact and covers the rest of the screens underneath of the fingerprint sensor. This was the only brand that I saw on Amazon that had this feature. After installation however there are massive air bubbles that will not go away no matter what. I am returning the item.

I put these on both mine and my wife's Z Force phones about a month ago. The packages state they are indeed for the Z Force. I have put multiple screen protectors on multiple phones and tablets, and I've never experienced any major issues before.Pros: Really good coverage, just like the picture. Really smooth and slick, feels like a touch screen should. Good packaging and instructions. So far they have survived multiple falls and slides across multiple surfaces (toddlers are rough on phones) with no breaks or scratches. Works well with the Incipio DualPro case.Cons: Mine did not stick at all above the speaker cutout and an area about half the width below it as well. My wife's adhered better and only has a quarter inch long bubble under the cutout. There were initially small bubbles around the edges of both phones as well, but they went away after setting a large book on the screens overnight.

Not happy with this product. The intake was ready but for a few bubbles that eventually went away. The one that didn't is from dust as it feel after I cleaned the phone. Not their fault. But the screen cracked after the phone was dropped..... On its back, in a case... So not sure how that happened but yea. The bottom was cut right to be fair just the front flash and speaker are not. Front camera was fine as well

First one I received came opened and folded in half. Obviously this meant that the protector inside it was smashed to bits and had to get amazon to send me another one.The next one I received was not bad. It is probably the best one of about 3 glass protectors I have tried. My only complaint is that this screen protector does not stick around the top speaker grill; feels like a common issue these days but still annoys me to no end. I am keeping it on until my sanity finally snaps.Note: Make sure you only order this protector if you have a Moto Z FORCE. These full coverage protectors don't play well with the curved edges of the regular Moto Z.

Perfect for the Moto Z Force. There's an updated version to this screen protector which I received. I'm pretty sure most of the bad reviews were for the old version because this thing installed flawlessly on the first try. Clear, fluid and full coverage just as advertised. A must have for the Z Force.

Absolutely the best screen protector for the Moto Z Force Droid. I love how it covers every inch of the phone and has cut outs for the finger print reader, flash, camera and microphones. I will be buying more. Super easy to put on since everything just lines up with the cut outs.