Nilight 2 Pcs 4 Inch 60W Led Pods with 2 Inch Tow Hitch Mounting Brackets Backup Reverse Lights Rear Light Bar for Pickup ATV SUV Truck Trailer Boat

I purchased this for my son's 2004 Chevy Silverado. He recently put window tint on his windows and made it difficult to see at night with his reverse lights on the tail lights. These lights are very bright and adjustable so you can point more towards the ground or straight out for distance with the adjustment on the bracket. You can also turn the lights to the right or left as you prefer. Installation - as others have mentioned, the bracket didn't fit around the hitch...on the outside. That is due to the chain loops. Our truck has a factory hitch and and the end of that is under the truck had just enough room to install these lights. I actually like how the lights now sit under the bumper. The chain loops very slightly block the lights, but they are so bright it is plenty of visibility. Also, as others have mentioned, the wires to the lights are short, but I used some short scrap pieces of wire to have enough to get to the trailer plug to tap into the reverse light wire. I just grounded the black wire to a piece of metal and it all worked perfectly. I would also note that there was no installation instructions included with this light, but there are some YouTube videos that help. I have purchased other Nilight products and they have all been good quality. I would recommend, but know that if the bracket doesn't fit around your hitch, you may have to get creative.

Did not fit H2 hummer. Sold to a friend. They seamed bright and of quality

The hitch on my '01 RAM is 2.5", and the bracket is supposed to fit, but it doesn't. My hitch does have a flange on it, and I also have a brake light housed in it. This is how I keep this unit in place, using the brake light to hold it in. The lights could be better. The wires are cheap, and too short. Adding more wire to these was just like mush. In addition, I didn't want to cut into my backup light wires, so I found another way. I connected the black wire to a good ground on the truck, and ran the red wire to my 7-pin trailer connector - the one in the center (most ports will label each pin on the outside cover - and the center pin is generally for reverse lights). A word of caution, make sure the battery is disconnected when you make the pin connection, and use a good female connector (you will likely have to bend the connector open a bit to make it fit over the pin). Also, wrap the connecter well with electrical tape to make sure there is no contact with any other pins, and fits tightly on the reverse light pin. Some other reviewers have mentioned that these light pods retain water, which is unfortunate, and I suppose I'll see if it happens when it rains. One option is to coat the edges with silicone. I just didn't see anywhere other than the front lens cover to seal. I still like these lights, and the bracket, but wish it was a better fit.

Quality was surprising. But, although it said it fit my vehicle (2016 Tundra), it did not. The trailer hitch was the right size, but the weld on it was too thick. Vehicle was previously owned so I'm not sure if that's where the weld thickness stems from, but it didn't fit. As for the product, I was disappointed it didn't fit. I was eager to get these...more disappointed that the quality of these were so high for how much these were and I couldn't use them. :( I seriously looked at other options to mount these but nothing I felt comfortable with. I hope these work well for the next consumer.

Didn't fit over receiver hitch

These lights arrived in a very timely fashion... they were well packed and showed no damage to the box. The instructions were easy to follow and installed in about 30 mins. Since I had previously wired in a different set of lights, (LED strip light units, that mount where your license plate attaches to the car... I had installed two of them. One above and one below the tag for the purpose of safe, night time backing up). Btw, if you're considering these units, don't waste your time/$$! They claimed to be waterproof, etc, etc... (spoiler alert- they're NOT!!!) They lasted about a year... A couple of weeks ago, I backed up in front of a glass storefront where I could see the reflection in my rearview mirror. Of the 24 "super bright XENON LED lights", one set was approx 50% lit, and the other? About 25% lit after just 1 year! (and I'm not sure how long I rode around like that!) On this unit, however, they are easily 2-3 times the brightness/range of those strip lights!! Since I just installed them, my review is somewhat incomplete... I gave them the highest 5 star rating in everything, except durability.... (only 3 stars so far, as time will tell, (with the durability of them). But I have a much better sense of quality with these than I did the orig ones, which I scrapped). Whew! that was a mouth-full! I chose to not buy the extra wiring kit with a dash mounted switch, (which I guess would be handy if you wanted them for say, camping purposes, setting up your site in the dark). I had some appropriate wire on hand, which I used to wire them directly into the backup light circuit of the vehicle. ANYWAY!! So far I am THRILLED in all aspects of this product, save for the durability...( which, I hope I'll remember to update the reliability factor in say, 6 mos. or so). Good luck with yours!! CHEERS!!!

Works as advertised. Would like it to be a little longer, but still works great.

My overall quality rating is because the lights and bracket is exceptional well made and I wish it fit and I could have used it as is. Initially felt the 8" wires are way too short to reach possible connection points on any vehicle without splicing in extra wires. Short-sighted detail for such a high quality assembly. The real problem was with the saddle that fits around the receiver. I have a new Ford Ranger with a factory receiver with no rust or damage yet but could not get the two halves to slide on. I had to mill about 0.040" off the inside before it would slide on. Also the receiver hitch fits very close to the edge of the bumper so I had to remove material from the top of one half.. Once I got it to fit properly I found that it fit too close to the hitch pin making insertion and removal very difficult. Decided to fabricate custom brackets to fit existing bumper mounting bolts to avoid drilling the bumper. I probably should have returned it but the lighting and housing are good quality. I'm sure the brackets will probably fit other receiver hitches and bumper configurations but unfortunately, not mine.

The product arrived in time and it looks very good. Unfortunately, it won't fit between bumper and receiver. Everything else seems to be okay but there is no way to get it in there. So it's not only the space between receiver opening and hooks, it also needs at least an inch or 1.5 inches between bumper and receiver. Great idea but I'll have to return it 😭

You have to be careful how it fits onto your tow point in relation to wire connections to trailer Would for fit on mine so it is now no use to me and have installed them on a totally different brackets Lights are great

very good price

Nicht zu Empfehlen.

Al colocar lo se adapto bien y lo pude asegurar, en general me parece muy buen producto