6 Bikes Rack

Super functional. Because of the design hanging on the wall it frees up a lot of space in your garage. Great for smaller spaces. They’re very stable and hold extra large bike frames with ease. They’re easy to install and took my husband under an hour. The bikes are stable while one the rack and very safe while hanging. I don’t worry about my toddler walking by them. Great value!

This bike storage rack has been a lifesaver for our family! It’s sturdy and holds all our bikes safely, which means no more tripping over bikes in the garage. Easy to assemble and makes getting the kids’ bikes in and out a breeze. Totally worth it for keeping our space tidy and stress-free!

Can you hang 6 bikes with this rack? Yes, but not as pictured on the product page with all three sections of rack being mounted side-by-side and flush together. It's important to center each rack across wall studs, or mount on wood paneling that is anchored into wall studs. Two bikes can fit on each section, but there must be spacing between the racks. This rack system is not made specifically for bicycles. In fact, the literature that comes with the rack doesn't even mention bicycles - it shows an assortment of attachments and tooling. It's safe to say that bikes would be the heaviest thing this rack system can handle, and proper mounting is key for stability and safety. Hanging & removing bikes from the rack takes care; pulling down on the bike could bend the hook, break the mount, damage the bike, or even cause injury. It's not something I want my younger kids doing, so only larger bikes for older children will be mounted at our house. Tips (also see pictures): • Determine how high to mount the rack by measuring and eyeballing your largest bike - lift it up off the ground as far as you want it to be and take note of the top of the front tire. The bottom of the rack should be mounted between 3 - 6 inches below the top of the front tire. My wall is unfinished, so I used the 3-inch approximation (no, I did not measure - just eyeballed). • Once you mark the desired mounting position/height, use a level to draw a line on two studs. Place the rack on the line and center it between the studs. Use the rack as a template to mark the screw position. • See how close to the edge the screw holes are? Yeah, that's my biggest complaint with this product - it needs to be about an inch wider for standard wall stud mounting. Make sure to pre-drill those holes to ensure screws are driven in straight and the studs do not split! • Once the rack is mounted, pop two large hooks on each end as far apart as possible. • Different size bikes should be mounted side-by-side on the same rack to minimize petal & handlebar interferences. I rate this as 4 vs 5-stars because the racks are not wide enough for optimal mounting on studs, and I am somewhat concerned that bicycle weight may be pushing the design limits.

Put this rack up in our shed and it saves so much space!! Good quality and easy to install.

These worked so great! I took some wood and secured it to some studs in the garage wall. And then screwed each bracket to the piece of wood. Each bracket holds two bikes. Completely secure and won’t pull out of the wall.

Not as sturdy as i hoped but it will get the job done. comes in 3 sections. Plan on spacijng the sections apart quite a bit to fit bicycles in. Otherwise you iwll have to remove bicycles in order from 1 side to the other. If you space out the sections you can select bikes from any position on the hanger.

Great rack. I caught it on sale for almost half off. Great buy easy to use. I put a 1x6 behind it since it wouldn't fasten to 16" centers. But other than that can't complain does as it should

The overall length of each unit is 16”, however, the drill holes are 15 1/8” apart, so you’re only going to hit a stud on one side. They provided drywall anchors with this unit, likely for that reason. If you put one end in a stud and drywall anchors on the other end, it will rip out of the wall as soon as you hang just one bike. We tried it and with just one bike, which was a carbon bike so extremely light, and the rack ripped right out of the wall and bent the rack in about 1-2 seconds. The rack is supposed to hold more than one bike and most bikes are made of aluminum which is heavier than the carbon bike we put on it, so the only way this rack can work is if your studs are a little closer than 16” and if they are exactly 16” on center you might get lucky and grab a little edge of the stud. We are going to go to the hardware store and buy a 2x4 board and drill that directly into the studs and then we’ll mount the rack to the 2x4. That should work, but it won’t be pretty and requires the purchase of the wood, which is expensive right now and of course the trip to the hardware store. For these reasons, I’m giving 1 star.