Rvinyl Window Tint Kit Compatible with Chevrolet Silverado 2001-2006 (4 Door) - Complete Precut Kit - 5%

These fit the front windows of my 2001 Chevy Silverado like a glove. I took the extra steps and took the door panels off, lifted the lower window seal. To do both windows only took about 45 minutes, and that includes the time it took to remove the door panels. I used a rewards card. I also put soapy water mix on the inside so I wouldn't scratch the tint. About the only problem I had is I didn't wipe the soap mix off the outside, and thought that it was on the inside so it took a bit of time before I realized my mistake. With this tint I didn't have to cut or trim anything. I wish I could give more stars, but this is a great product, and whenever I need more this will be my go to company

I dont generally complain but....I dont want anyone to have this experience. Got tint and being 2nd time i have did this figured it be a snap. Read directions (kinda hookey) and watched a brand specific video on install. The film on back, which is not marked, was crazy hard to separate. Took 30m to get it loose even with the supplied stickers. Then when separating the the tint from the film it felt like stretching it since it pulled really hard. Okay got it off. Went to pass side door. Did the soapy water etc. Fit was good but it too long so after getting 99% on glass trimmed the lowest point and fit was fine. BUT it would not set down on glass. Like it had been stretched out when peeling back off. Tried some heat and harder and softer squeegeeing and to no avail would the film adhere properly along the edge and in top 1/4 of glass. Like I said felt stretched. After 30-40 min I gave in and removed the tint so it would not be stuck looking so bad. So I went to the drivers side. Made triple sure everything was clean, wore my nitrile gloves and had warm soapy sprayer. Peeled film off, hard again, and set tint on soaped up window. The top and ack edges would not quite square up. it set down clearly better than the 1st side did but the 3 showing edges just would not line up. And it was def way longer on bottom. After 20m I decided this was not acceptable nor going to ever look right and prob peel since the tint would not fit clean enough on edges. I asked for a refund explaining my situation or even a new set to try. Nope, I dont have evidence of it not fitting. Like I was going to leave it on and let it dry looking hideous and not being able to open the windows. Just sick how they dont care at all about the quality of their product. All I wanted was a a "hey sorry, try another one.". But nope full "not us, thanks for your money.". Just be thoughtful if a Rvinyl product is flawed you have 0 chance of recourse. Thanks for reading.

5 stars all day. this tint is amazing quality! im forever sold on precut tint! it layed on easy and was a perfect fit! i will be purchasing again for my other vehicles.

Didn't cover glass 100 percent

Buy it! Cuts were near perfect and it turned out great. For the easiest method I took my windows out of my truck and tinted them right on my kitchen counter but overall good product.

Easy to Install. Easy to remove from backer. Let it sit for 5 days before using window. One small section is curling. Did my truck 2 weeks with another tint. That one is good.

Fit was great

Update2: Tried reaching out to seller with no response after 3+ weeks. As stated below, save your money. Poo quality and poor customer service.Update: It is junk. Stay away. I did my best working around the poor cuts but within 5 times opening the windows, it lefted and dragged rips across the glass. If you're lucky enough to get clean cuts then you may be fine but their quality control is terrible.I'd say look elsewhere. It wasn't terrible, but the cuts were pretty bad. I was left with jagged edges that tore. For what it is, I guess it is ok, but I'd have hoped for a little better cut quality. I'll leave it on until it inevitably peels up.