Slime 1051-A Rubber Cement, Tire Repair, use Plugs or Patches, 1 oz. Tube

I have gone thru cans of these 1050 Slime rubber cement (though only a small amount is needed) in patching tubes in this lower income city of cheap bike (mostly), using inexpensive patches, and can attest that it is very good (used correctly), and is the best for the money (8 oz. for under $8.00).Unless the puncture is too large (see below), patches using this do not come off upon inflation, with the exception of certain tubes which are not made with the normal rubber. Such have a slippery surface and despite buffing the cement will peel off once day. However, if you remove the first coat and reapply the cement and let it dry and apply the patch, then the patches will hold.Note there are basically three types of tube flats (aside from a bad valve). One is due to a puncture, such as it caused by glass, wire and some other sharp object. Another is that of pinch flats, caused by hitting a curb (like due to faulty "bunny hopes") or something hard, resulting in two horizontal flats in the same area of the tube, sometimes on opposite sides. A third cause is abrasion flats caused by a hole in the tire,. usually as a result of "drifting" (skidding). If a hole in the tube is larger than a very small hole then you should replace the tube (often cheaper to buy as 4 packs from a certain mart).Basic instructions in patching a tube:1. Remove the wheel (axle nuts, if used, are usually 15mm) and deflate the tube (cock the pump nozzle to one side so you hear air and rotate the tire somewhat). Then remove the tire from off the rim (if necessary, use a tire lever to pry off one side of the tire, beginning a foot away from the valve, and after one side of the tire is off then carefully push any of the tube up into the tire, then squeeze the tire and then push the tire lever all the way under the tire, lean the tire to the side and slowly pry it off, carefully ending with the valve).2. Find out the specific location of the tire leakage by inflating the tire (maybe about 6 pumps using a full pump as this $10 one) until it is spongy like a balloon (you can press it in about an inch) but not stressed. Then, if leak is not found, rotate each side of the tire past your cheek so you can feel the leak. Or, if necessary, vertically submerge each section of the tube in water (begin with the valve) and look for bubbles.3. Next, clean/dry the area around the leak and if necessary use a marker to make a wide circle around the leak so that you know where it is. Note that if possible, it is best to leave the tube inflated until we get to step 6. Also, try to have clean fingers and minimize skin contact with the leak area.4. Next, use a buffer to friction-clean the wide area around the leak (blow away any sand if you use sandpaper), and then spread a thin coating of rubber cement onto the leak area on the dry tube, rubbing the cement into the tube for a few seconds until it begins to dry. Note that it is best to use cement that is made for rubber patches, like Slime 1050, and DO NOT use super glue or anything else but rubber cement!5. Next, let the rubber cement dry for about 2 - 3 minutes (outside in windy or sunny warm dry weather it can dry faster), while you slowly remove the foil backing from the patch, holding the edge of the patch. You may also remove the cellophane cover if you want, since that does not stretch like the rubber does - but AVOID putting your fingers on the bottom of the patch (where the foil was).6. After the cement is dry (it will look dry) deflate the tire if there is much air left in it, and then place the patch over the center of the leak. Then place the tube on a smooth hard surface and press down all areas of the patch7. Wait about a minute or two before putting some air into the tube (about 4-5 pumps) to make sure the patch is holding and there is no leak (note: some tubes are made of a different material which feels very smooth, kind of like plastic, and for these you may need to repeat steps 4 and 5 if the patch begins to peel off). If all is well then place the inner tube into tire and onto the bike and re-inflate it until tire is firm, (about 16 pumps or more) then stop. Do not over inflate (the side of the tire will tell you the max. PSI and you can check your pressure with a gauge).Hope this helps.

I plug hole good. My favorite part is when the glue shot back at me under the pressure of the tire.Remember to safety squint kids.

Works well with my tire repair kit

The cement arrived quickly and undamaged. I have not used it yet.

Always keep an unopened tube in your cars road kit

Great

it works ok

I used two types of tire repair methods. Neither of them sealed perfectly so I was hoping this glue would assist them. No it did not. It takes forever to dry out and it never really seals anything because it just drips off and away from where it needs to be. It just doesn't stick well. It does, however, stick really well to your hands. Probably I don't know how to repair tires yet but I'm working on it. This did not work for me. I settled on the screw type tire repair and I just needed this glue to help it work better- not the whole solution, and it just didn't even manage that much.