P3D4-10 Punch P3 4-Ohm DVC 10" Subwoofer

When I initially purchased this subwoofer, I planned on seeing if it would run on the factory amplifier in my car would run this ok. I ended up building a combination fiberglass/MDF enclosure that would put a large portion of the sub box in the side well of the trunk of my car. I was able to get about .6 cubic feet of space while only taking up a few inches of width from my trunk. Through googling around, the oem amp in my car was about 40 watts RMS. This was enough to run the sub ok. I did notice that I needed to increase the bass and subwoofer level on the head unit to get a balanced sound. The bottom line was that this sub needed more power, so I purchased a punch 300x1. I chose this amp for several reasons: 1) The 300x1 did not require a remote turn on and was able to accept line level inputs up to 10v which meant integration to my factory stereo would be a snap. 2) The 300x1 is class AB which should have a higher damping factor than a class D amp 3) The 2 ohm power of the 300x1 was right in the sweet spot for this subwoofer.(around 450 watts) After installing the amp, this sub really shines. I believe it has a 16mm one-way xmax which is about 1.25" of excursion both directions. At full power, this sub moves air. I would estimate the SPL in the high 120s if you care about that sort of thing. Initially I did not add polyfill to the box and felt that it would play down to about 30hz at a decent level. After adding polyfill I think the sub will easily play down to 25hz or so now over 120db. I did notice that adding the polyfill did reduce the perceived loudness between 40-80hz somewhat. Subjectively, I would say this sub generally sounds good for most types of popular music. My music collection spans classical, to 80's and 90's hip hop, to 60s and 70s classic rock, to more recent indie/college radio pop. I have a record of some pipe organ that is rendered flawlessly at even the lowest registers and really makes the music visceral. Things with an 808 style kick are nice and fat and boomy(I always like to demo this sub with Beastie Boys Hold it now, Hit it). Another great track to demo this sub with is breathe/on the run on Pink Floyd Dark Side of the Moon. The synth/organ bass is a lot of fun to hear through this sub. That said, I don't think this sub is "perfect". This may be due to the sub having a somewhat heavy aluminum cone/voice coil, but the transient response is somewhat smeared. While you definitely "feel" a good kick drum, its not quite as punchy or clean as it should be. Some of this could be tuned to not be very noticeable, and I don't really think its a huge problem, but its definitely not the most transparent sub out there. I think for most people that is fine or even desired. Another thing to note- this sub is big and heavy. The basket and magnet assembly takes a lot of room. I had to actually remove the rubber cover from the magnet to make it fit in the tight confines of my enclosure, since it was fiberglassed to fit a very specific spot in my trunk. So for those of you working with tight confines, this may not be the sub for you. If you have room to spare, then this sub will not disappoint!

I have this sub mounted in the Bbox single 10" box on Amazon, driven by the RF Prime 500x1D amp, and THIS SUB POUNDS. PERIOD. Couple of tips: 1. Make sure you're getting enough power to it. Going with the 500x1D RF amp is a good move (or another honest 500W+ amp at 2 ohms). Less power, and your signal will clip. It will handle a little too much power better than it will handle too little power. My RF 500X1D is certified to push 628W at 2 ohms through a 50 amp fuse, which is pretty much perfect for this sub. Match the amp to the sub, 80%-120% of the sub's RMS power capability. It has aluminum VCs and and aluminum cone. It sheds heat like you wouldn't believe. If you want to drive this with the RF 250 amp or something comparable (like any of the cheap mono block amps on Amazon that RMS ~200W-300W), please consider the P1/P2 subs. They are more efficient, lighter, and have less power requirements. They'll work well with smaller amps. This sub will not as it needs more power: it's heavy, not efficient for a 10", and has a VERY heavy motor structure that requires a lot of power to move it. Also, spend an extra $50 and get a good amp. There is no way a cheap amp is hitting 1000W with a 20-30 amp fuse. Do the math; it's impossible. 2. Make sure the mounting board is at least 1" and the box is the proper size, ~ a little less than 1 cubic ft. I used the single 10" Bbox on Amazon (http://www.amazon.com/gp/product/B0013N0UCQ/ref=oh_details_o08_s00_i00?ie=UTF8&psc=1), modified it by removing the clip terminals to handle bigger wire and caulked the whole thing including the sub for no leaks. WORTH THE EXTRA 5 MINS!!! No box resonance, which is important on a sub like this: the excursion is 1" or more, it's heavy, has a heavy motor structure, heavy cone assembly, and really just pounds. It needs stability to sound good. 3. I'd suggest a sealed box over ported box. Sealed goes a bit lower in frequency, has a flatter response curve, and 10" subs tend to hit tight and quick, which sounds better in a sealed box anyway. You'll lose that flatness and quickness in a bigger sub, or a ported enclosure. If you are going for SPL, you'll likely not be choosing a single 10" anyway, but if you do, know that this is the best one I've heard if it's mounted/powered properly. With the over 600W RMS @ 2ohms I have going through it in a .79 cubic foot box, it hits as hard or harder than any dual 12"s I've owned up to now, including bandpass/ported enclosures, and more power. The key is the excursion: the 10" cone is smaller, but the throw is longer, so it still moves a LARGE quantity of air. The specs say it doesn't hit 10Hz, but I've tested it and in my sealed box with the RF500X1D pushing it at 2 ohms, it hits 10Hz (can't really hear it, but the sub is moving and I can feel it rattle my seats and ribcage) through 70Hz flat and clean and HARD. It's best between 20Hx-60Hz, which is exactly where you want a sub to be. And you can FEEL it knocking the wind out of you; not just hear it, although it sounds great and tight. TL;DR: Put enough power through it, seal it properly on a thick mounting board in the right sized sealed enclosure, and this sub will shame many 12"s, even dual 12" setups. Good, loud, tight, hard-hitting bass. It's unbelievable, and it's RF, so you know it will last. No regrets, it pounds, and I still have most of my tiny trunk left in my MINI S. Awesome! UPDATE: designed/built new custom box out of 1" MDF on all sides, to the exact volume RF recs in the instructions, and this thing hits even harder, which is unbelievable. It has also been playing trouble-free for a year now. I will be buying a 2nd one of these for my 4runner trail toy.

I recently purchased this (single) RF P3D4-10 and am running it via Rockford Fosgate R500X1D Prime 1-Channel Class D Amplifier (both purchased from amazon) I have owned several subs in the past and feel as though it deserves a fair comparison. This single 10 inch sub vs 2 10" JL Audio 10W3 and JBL 500 - The clarity of the bass and the response time is outstanding when compared against both my JL Audio and JBL subs... this single sub seemingly blows them away. when it comes to sound quality, albeit it does have a much higher RMS than either of my previous subs. The specifics of how this sub is being used: CAR: 2012 Subaru outback (with harmon kardon system, HK rear subwoofer disabled). Enclosure: Sub is mounted in a sealed enclosure encased in the tire well (insulated and fiberglassed and box constructed with 3/4" mdf) Music Style: Primarily Metal, some hard rock, some industrial/techno. Tuning: Sub is hooked up with total resistance of 2 ohms to Rockford Fosgate R500X1D Prime. -Amp punch eq set to max for more peak resolution in the lower level, and crossover set to max (250 Khz) and then I am using the crossover on my head unit (Pioneer AVH-5700 BHS) to dial in the sound i want. With previous subs i would get a lot of rumble/distorted bass, with sub, when tuned properly, i am able to control the punch of the bass very well. Heavy double-kick rhythms are not lost, each note is clear and punchy and compliments the system very nicely regardless of artist or genre. I was torn between a dual set up and a single sub, and am very happy i went with the single sub set up...it is more than you will ever use. I can't even turn the amp up half way without liquifying my brains and sh*tting my pants. If you are looking for a powerful, clean sub, with great response and superb clarity, you can't go wrong here. Go get one.

So first off, let me say that this thing is very well built. The aluminum cone and trim ring looks just amazing. I've seen that Rockford throws magnet boots on their subwoofers and underneath is a tiny magnet, the magnet underneath the P3s are not small at all. Enough with the cosmetic features though. Getting to the actual performance of the sub, For the $125 I paid for this subwoofer this has to be the loudest 10" Sound Quality subwoofer I've ever heard. The notes this thing can hit are absolutely amazing. I have mine in a to spec sealed box with insulation and being powered by the Alpine MRV-M500 and is wired up by KnuKonceptz Colossus Flex 4 gauge OFC wires. The subwoofer does need to be broken in, but if you are using the same amp and sub, for the best quality sound and to be heard, set your gain about 3/8 of the way, Set the LPF to 100-125 Hz, and. Don't even touch the bass boost as it distorts the woofer at one note. When you do this make sure to break in the subwoofer for about 2 weeks to a month, then you will see why they simply call it "Punch". 5 stars.

I was looking for lower bass for my country, rock, and metal listening. Don't listen to hip/hop or rap. Space, weight, and power (current draw) were huge concerns of mine, so larger drivers in low-tuned ported enclosures were quite out of the question. I'm also more Sound Quality oriented; but I'm not afraid to adjust to volume knob to 11 if need be. With an F3 of 36Hz and a Qtc of .783 in my 1 cu. ft. sealed enclosure, I'm now able to hear the lower bass guitar notes (typically around 40hz) now play with much more gusto than my previous sub, a Treo SSI. It's being fed by an Alpine MRX 500w amp, and crossed over usually between 60 or 80 hz; my front stage handles midbass quite well. So this sub is left to do the lowest work while still providing a flat response, at least as where my ears are concerned. Granted, in my sealed enclosure, it doesn't like the low 30s and 20s that you might find in rap. I'm certain a ported enclosure would do much better for lower extension. However, for my application, I'm quite pleased with it. And yes, it will still blur vision and bring rock-concert SPL if I want it to, but I won't be entering any dB drag races with it. Added bonus is that it is considerably lighter than my Treo sub. I believe the ferrite is under 100oz, despite the motor structure being quite portly and strong.

Excellent quality And it is expected from a company like rockford fosgate Ran these 10s in parallel to get them down to 1 ohm I have a punch 1000x5 @ 1 ohm this amps dynamic power rating on the sub channel is 863 watts The P3 can handle it with no problem The enclosure I used is the smallest you can go with 10s as advised by rockford fosgate 1 cubic ft. per sub Nice punch, deep bass but not overwhelming

I did not expect much for this price, I used other famous namebrand subs for $400-$500, but I read the reviews and decided to give this one a try. Wow! It sounds wonderful for its price. It definitely sounds "punchy", it hits very fast and clear. I do not think it goes very deep, but it definitely shakes my car. In fact, it is the first 500 Watt RMS sub that actually hits this strong. It also sounds very good with my Morel speakers, in fact I like it more than SQ sub that costs 5 times more. I am feeding it 500W RMS from PDX-V9 amp. It sounds good with any music, but it really shines with EDM/Dance/Trance tracks.

First off I will admit I'm an avid Rockford fan but primarily just there amps. I have been using them since I was a teen during the early 90's. I have never owned any of their speakers however. I consider myself a bit of an audiophile and poor sound quality isn't something I can accept! I always wondered about Rockford subs though and because it is a company known for raw power and attitude, both qualities I like in my bass reproduction I decided to try this out. The price was excellent too which helped me decide(not a lot cash tied up if I didn't like). As far as use goes, I installed this into a small sealed box (.55 cubic ft. Loosely stuffed with poly-fill) which is great and doesn't hog space in your vehicle. I power this with a Rockford power series mono amp and it delivers about 500 watts rms to this sub which is perfect for this model. It sounds pretty darn good . It has deep authoritative bass that has a nice tone to it. It seems quick and responsive and more articulate than I had expected it would. It does seem to have a sweet spot and I can hear this subs limitations if pushed however. I'm considering listening to it in a ported box just to see if I like that better with this particular sub. Overall for this price I recommend but for the m.s.r.p if bought at an authorized dealer there are much better choices for sound quality. If good performance, good value, looks and attitude are important to you this is your sub.

Excelente producto, la marca lo dice todo muy buena calidad en audio, bastante potencia con el amplificador adecuado y el cajón correcto un monstruo.

Très bon sub, qualité excellente

Nothing to say negative about this bad boy! Crisp thunderous sound!!

Installed these in my Ram 2500 crew in a Fox acoustics box. Pushing them with a RF prime 1200 w amp. Absolutely thunderous!

I bought two of these and paired them with a powerful mono amp. In a sealed box these things hit hard. I’m very happy with these subs