Hogue OverMolded Rubber Monogrip for Taurus Models 85, 94, 380, 605, 650, 651, 850, 851, 856, 905, and 941

I wanted to replace the wood grips that came with the gun, a Taurus 327 Federal 2", because they were too thin and had no texture. These were a perfect fit that only took minutes to install. Very comfortable grip that makes the gun balance much better with just the right amount of texture.

Fits like a glove. Perfect upgrade for my 856. I recommend if you’re considering changing the hand grip. Inexpensive and good quality. Oh and it is rubber not plastic.

I should start by saying there is nothing really wrong with the factory grip on the 605. it's just a bit small for my hand and leaves my pinky hanging. The Hogue is the ideal solution for me, adding about 1/2 inch to the grip length which allows me to grip with a full hand. I also noticed a slight change in ergonomics because the Hogue leaves the frame backstrap exposed rather than covering it with a layer of rubber, as does the factory grip. This makes the grip angle more comfortable for me, more like a 1911 grip angle. Installation of the Hogue was duck soup. Took about 10 minutes. That does not include removal of the factory grip on the 605. That's a challenge! For removal, you'll need a 3/32" punch and a real hammer (not a punch mallet), plus a non-marring block, because you're going to have to really whack that punch to get the pin out.The Hogue is worth far more than the modest price to me. It makes shooting the little 605 more accurate and more fun!

I bought one about a year ago and had major issues installing the first one on my Taurus 605 with the factory roll pin. I ended up stretching it too much trying to fit it over that factory roll pin and just threw it in the trash. Then I read through some reviews here for advice and decided to order another grip along with a more appropriately sized replacement roll pin with the recommended shorter 1/2" length. Turns out this time Hogue included a proper-sized roll pin in the box taped to the back so it doesn't get lost. The grips fit perfectly with that pin. But for those who lost their pin or didn't get one, 420 Stainless Steel Spring Pin, Plain Finish, 1/8" Nominal Diameter, 1/2" Length (Pack of 100) is the exact same size pin as the one Hogue includes in their kit. This grip is NOT meant to install over the long roll pin that's included inside the newer factory Taurus grips, there is absolutely no way for it to fit without major forcing and possibly shaving out some grip material, it's not supposed to be that difficult, just get the properly sized pin, line it up, and then it goes on no problem. Don't overtighten the bottom screw either, it throws the grips slightly out of alignment along the frame, plus the screw has a tendency to slowly walk out over time anyway when firing/dryfiring. Instead, put some blue threadlocker on it and just tighten the screw to the point where the grip is aligned seamlessly with the frame.As for function, I never tried the factory 605 grips but when firing .38s it's about as comfortable to shoot as my dad's 6" S&W 686 with .38s although there's inevitably a little more muzzle rise with the reduced weight of the 2" barrel on the 605. .38 +P has a little more oomph but still not bad, so these grips would probably be absolutely perfect on an 85 if that's what you've got. I also tried some 125 grain .357s and although I could feel it in my wrist a bit, my hand felt fine which I think means the grips did well. The muzzle rise was a bit high but I think it would've been worse with the factory grips where your pinky isn't making full contact like this grip does. It starts to get a little bit painful after 25 rounds of 125 grain .357 but honestly the concussive blast from a .357 coming out of a 2" barrel is worse to me than whatever wrist pain I'm getting when firing them. I would still like to try some 158s just to see how bad they are, I've heard they pack quite the wallop when fired from such a small gun. Speedloaders actually fit and work fairly well now with the Hogue grip, the thumb shelf on the factory grip made them impossible to use before.

Here's the good, bad, and ugly about this grip on the Taurus model 85UL 2016 production line.The good: compared to the actually not bad "charging bull" stock grips, the Monogrip provides a much better purchase, as most people's pinky will find a home on the grip, and not dangle off of it. My normal sized hock wraps nicely around the grip, and it is extremely comfortable for me.Additionally,. The stock grip got in the way of using speed loaders. I got around this issue by trimming a small part of the stock rip off on the cylinder side. This grip, however, works nicely with speed loaders. No issues....The Bad: while the grip fits nicely (with an exception detailed in a minute), installation for my particular firearm wasn't as simple as they say. The new Model 85 grip is apparently attached differently. It utilizes a small pin that holds the stock grip on place. This pin comes out with a few firm traps with a punch and hammer. The problem is, though, that this pin will not work to hold the Monogrip in place. The Monogrip uses a screw at the bottom to secure the grip. This screw is held in place by an included clip, which secures via the grip pin. On my particular model year firearm, the pin that is used to hold the grip on place will not work for this. It is too big. I ended up using a small cotter pin instead. If I didn't happen to have a small enough cotter pin, I wouldn't have been able to install it without having to purchase an acceptable pin.The ugly: The grip feels great. It is nice and tight on the frame, now that I got it properly secured.. However, it left a tiny open gap exposed on the frame which is normally covered by the stock grip. This is a working gun, and as such, may be exposed to dirt, rain, or even the inside leather inevitably rubs off a new holster's inside until is smoothed out, unless you take the time to condition the inside of it well first.While I don't anticipate any real problem with this little gap it would be nice if it wasn't there at all. After all, why take any chances? Needless to say, I really don't care for anything at all that may potentially affect the function of my firearm. While I don't know if anything that would be small enough to fit through will actually cause any real issues, I would rather not have grit and dust bunnies getting in there.If you're willing to overcome the aforementioned issues, then this would be a great grip to put on your Model 85. Those with older versions may not have these issues. I honestly cannot say for sure. But I felt compelled to share my experience with the 2016 production model.

Hogue grip worked real good very tight fit.Pin that came with it was loose fitting.Got it together with not much effort. Nice grip.

Good quality and easy to install that cannot be found with others.

This grip fits perfectly on my Taurus 856 and has a better feel over the factory grip. I will be looking into Hogue for my other firearms.