12001541 303373K Dryer Drum Roller Support Wheel Kit for Maytag Kenmore Amana Crosley Admiral Dryers Replacement Parts #303373、Y303373、3-3373、12001541VP、W10116741、ER303373K、EA1570070、AP4008534

works on my maytag Neptune. The roller above the heater tube goes bad because the heater is inches from the black rubber on the roller. a design flaw. So now I keep a 2 pack on hand so I can replace when needed. I just followed a good FIY video and now I can do the replacement in 30 minutes. I have replaced the right side axle once, the left side roller once, and the right side roller above the heater twice.

"Is there a thunderstorm today? I thought the forecast said it was clear!" ... "Nope, that's just my dryer..." Has this ever happened to you? Have you found yourself so embarrassed because your dryer rumbles like thunder? Are you saddened by squeaks, squeals, bangs, booms, and thuds from your once quiet and happy clothes drying appliance? Chances are, your drum rollers have bit the dust and need to be replaced. This kit contains everything needed to replace the stock drum rollers with an OEM-like fitment. The rubber feels stronger on these rollers, and the bearings are a tiny bit noisier than OEM, but they roll very smoothly and very consistently. The shape and size are identical to OEM, and the only real difference is the fiber washers. In my install, I used the new fiber washers in the back where my originals were pretty much dissolved, and purchased some others to use in the front instead of the goofy flat bendy washers. The new clamps in this kit are way better than the OEM ones, and the thickness of the fiber washers is also greater than OEM. The replacement shafts are basically identical, with these having maybe an extra .5mm to 1mm length, which actually made installing extra fiber washers a breeze. My Maytag Neptune dryer has not been serviced properly prior to my owning it, and it still had its original drum rollers. Only one fiber washer was used on each side and only one goofy metal washer on each side. It sounds like some other models that other reviewers have mentioned contain two fiber washers instead, but this kit fit my machine perfectly and needed no extra parts. I only chose to use fiber washers the whole way around due to some bad experiences with heat, metal washers, and bearings in RC cars.

My dryer started squealing pretty bad and I feared for the worst. 4 screws out and the dryer came apart. The culprit was a seized roller. This part fit perfectly and returned the dryer to normal quiet operation.

I dislike that thrust washers won't slide over drum roller shaft. Seller needs to open a package and see what I mean if they are going to sell this kit. This is BS and I bet they don't give a damn about this issue ! The drum rollers are fine and so are the axles. Sell a kit with compatible parts or don't sell it !

Started getting an annoying squeak from the dryer, investigated and found the rollers were dry and breaking down. Put some bearing grease on the sleeves and let er rip. Got another 3 months out of it before it came back. Found these under $20 figured it was a no brainer. Just sucked having to take dryer allllllllll the way apart again. I've had this installed for a week or so about 20 loads- does the trick. I still put some high temp wheel bearing grease on the sleeves just for S and G. Time will tell if these will last as long as the oem maytag ones.

The installation was fine, and the fit seemed perfect. After just 7 months, I started hearing it rumble again. I didn't think it was the 'brand new' rollers I just installed, so I prepared to replace the felt pads I knew were old and needing replaced. I finally got into it, and realized that the felt pads were completely torn apart because one of the rollers had completely failed. When I lifted the drum, the roller fell off the bearing stud. The other bearing is still attached, but in bad condition. It will fail in less than a month. These lasted about 6-7 months. Yes, I lubricated the stud with high temperature bearing grease.

Fit as expected, replaced completely worn roller so made a huge difference in noise the dryer was making.

They seem to be a good fit and were quick to install - the axles are slightly longer than the ones I replaced, which makes it much easier to install the c-clips. However one of the roller wheels was lopsided and the drum isn't quite rotating freely. It's fine for now but I don't expect it to be a long-term fix.

No me enviaste lo ofertado, solicité un jueves Rodajas para secadora Maytag y me enviaste una bolsa